Mine's RB20 BH ECU, RB25 S1 parts, KA 5spd parts

[AE_Racer]

Got a few things leftover from my swap...

Gainesville, FL
PM for quick response..

Trades - offer up anything for S13/Rb25

Mine's ECU SOLD

All parts below from Series 1 Rb25

A/C compressor with bracket and tensioner.. Tensioner pulley has a small dent on the edge but should be able to bend it back. Unknown condition of compressor came with swap didnt use.. $80

https://sphotos-b.xx.fbcdn.net/hphotos-prn1/562146_10151589184180362_74694242_n.jpg

Lower harness uncut, EnemyS15 is selling an upper harness so you could have a complete set... $60

https://sphotos-b.xx.fbcdn.net/hphotos-snc6/6142_10151589184040362_569482372_n.jpg

(the wires you see cut are the other side of plugs)

OEM motor mounts, good for you guys going the r33 crossmember route. Look to be in great shape. $50

https://sphotos-b.xx.fbcdn.net/hphotos-snc6/269333_10151589184105362_754688863_n.jpg



KA 5spd non abs driveshaft, pickup only. $50

https://sphotos-b.xx.fbcdn.net/hphotos-ash3/599666_10151588562425362_1020252077_n.jpg


Also have a 5spd trans crossmember and sohc 5spd ecu but no pics at this time...

[DopeDougie]

Can you part the back piece of the driveshaft that bolts on the differential & the pin or bolt that holds it together?

[AE_Racer]

Need to keep it all together sorry man.

[wrxkid950]

ill give u $75 shipped to nj for the drive shaft

[DopeDougie]

Need to keep it all together sorry man.
I'll take the whole thing if you will ship it

[AE_Racer]

Not interested in shipping the driveshaft guys unless you're gonna pay for me to take it to the ups store and have them box it up. I don't have the time or resources to box and ship something that size. Thanks

[DopeDougie]

Not interested in shipping the driveshaft guys unless you're gonna pay for me to take it to the ups store and have them box it up. I don't have the time or resources to box and ship something that size. Thanks
I'll pay for it, pm this price with getting it shipped. If you could over night it, I'll pay for that too

[anti tyler]

dude search your local junk yards......

If you get tired of all this and decide to part the shaft out. I need the rubber vibration dampner.

that, unfortunately, is the mystery piece that doesn't even show up on nissan's 240sx diagram @ the dealership.

[DopeDougie]

I already tried

[AE_Racer]

Ecu sold. I wont have the driveshaft in my hands til saturday since it is with my s13 where im working on it. If you really need it that bad shoot me a pm and we can work something out.

[anti tyler]

well for my situation, the dampner is a vital thing, once mine shears apart then i'm dead in the water. there are ZERO! 240's in the junk yards around here. & quiet frankly i'm not going to dish out any significant amount of money for an entire DS.

So if and when you get around it, find out what homie want's to buy the end pieces from you for, and let me know what kind of price you can do on the dampner to maybe equal out to your originial DS price.

[AE_Racer]

I assume youre talking about the carrier bearing, so if its non existant in the nissan catalog here ya go. List: Carrier Bearing/Center Support Bearing - 1991 Nissan 240SX | O'Reilly Auto Parts (http://www.oreillyauto.com/site/c/search/Carrier+Bearing!s!Center+Support+Bearing/01418/C0362.oap?make=Nissan&model=240SX&year=1991&vi=1209002)

I may break it apart though cause dougie needs the whole rear section. Ill let ya know.

[Alan_405]

Was harness from manual or auto? Zenki or kouki?

Interested

[AE_Racer]

Was harness from manual or auto? Zenki or kouki?

Interested

Neither, it is for an rb25 s1, as stated above the parts listed for sale..

[Conrad 2NR]

Do you have the plug that goes into the ECU, a white plug? I need just that with a bit of harness still attached.

[ProjectZenki]

You might be a life saver. Really need that manual crossmember. Awesome! You still got it? How much? What part of FL? I'm in JAX

[AE_Racer]

I have the ecu plug, its broken in half in the center but iguess if you really wanted you could use it..

The trans mount, sorry bro the engine and trans were in a scrap pile with the mount still attached and it was hauled off.

[ProjectZenki]

Damn. I got a solid mount. I just need the manual crossmember.

[Conrad 2NR]

Thanks for the offer but I'll pass.