R33E8
04-05-2013, 07:58 PM
First up, brand new Full-Race T3 twin scroll manifold with a 44mm wastegate flange for the KA.. I has a nick on the flange that can be sanded down or left alone.. It was never even mounted, I'm selling it because I'm going bigger..
Asking 1100 shipped + paypal fees OBO
http://i.imgur.com/5Osj6xGl.jpg
http://i.imgur.com/QEEWzu2l.jpg
http://i.imgur.com/tQgLdiXl.jpg
I have a Precision 6466 turbo with probably around 3-400 miles.. Never went over 14lb's of boost and never had a problem. It comes with a T3 .63 5-bolt exhaust housing.. I might be able to supply a T3 .82 V-band exhaust housing for an extra $150.. I always ran it with an XRP inline oil filter and intake air filter so it's super clean.. I can include the -4AN feed fitting but the drain flange is not included.
Asking 1550 shipped+paypal fees OBO.
These are pictures of when I first got it.. It's the one on the left...
http://i.imgur.com/S5dq9h.jpg
http://i.imgur.com/YPp1ch.jpg
It's the one with the orange tag...
http://i.imgur.com/3IyQL.jpg
I have a stage 2 snow performance meth injection kit with a bunch of nozzles to set you up for direct injection any way you want..
It comes with the 3L tank, high pressure pump, stage 2 progressive pump controller for MAF systems (also works with MAP's and standalones), 1 625cc/min nozzle, 4 375cc/min nozzles (setup I had installed but never ran meth through), 1 225cc/min nozzle, 4 or 5 50cc/min nozzle( 4 of them are devil's own), 4 snow performance nozzle holders, 4 or 5 devil's own low profile nozzle holders, 2 anti drain solenoids, and around 25 feet of line..
I'm sure if you were to piece it together it would probably cost close to $1000 but I'm willing to let it go for $500..
Here are pictures of the 375cc/min nozzles with snow performance nozzle holders.. no meth has been run through them..
http://i.imgur.com/aS30gMC.jpg
I have a set of precision 1000cc injectors.. I got them cleaned and flow benched about 1000 miles ago... Will come with pigtails.. $255 shipped OBO
http://i.imgur.com/uUHslHEl.jpg
http://i.imgur.com/t5Ii1jf.jpg
s13 cylinder head with intact valve cover, s13 intake cam, set of s14 intake and exhaust cams $100:
http://i.imgur.com/0UkNJgq.jpg
http://i.imgur.com/Mx3zCn0.jpg
Full stock intake manifold with blocked egt port.. $40
http://i.imgur.com/HrlTN0f.jpg
AC compressor and Alternator - $20 each..
http://i.imgur.com/0x9vH7I.jpg
Stock pistons and rods.. The stuff that look like chips on the pistons is just oil absorbent.. the pistons and rods are in great condition -$40
http://i.imgur.com/s8rcYOI.jpghttp://i.imgur.com/91pVXwM.jpg
if you need anything else from the engine let me know..
I can be reached at 609 four five six 9773 I prefer text but will take calls on the weekend..
Asking 1100 shipped + paypal fees OBO
http://i.imgur.com/5Osj6xGl.jpg
http://i.imgur.com/QEEWzu2l.jpg
http://i.imgur.com/tQgLdiXl.jpg
I have a Precision 6466 turbo with probably around 3-400 miles.. Never went over 14lb's of boost and never had a problem. It comes with a T3 .63 5-bolt exhaust housing.. I might be able to supply a T3 .82 V-band exhaust housing for an extra $150.. I always ran it with an XRP inline oil filter and intake air filter so it's super clean.. I can include the -4AN feed fitting but the drain flange is not included.
Asking 1550 shipped+paypal fees OBO.
These are pictures of when I first got it.. It's the one on the left...
http://i.imgur.com/S5dq9h.jpg
http://i.imgur.com/YPp1ch.jpg
It's the one with the orange tag...
http://i.imgur.com/3IyQL.jpg
I have a stage 2 snow performance meth injection kit with a bunch of nozzles to set you up for direct injection any way you want..
It comes with the 3L tank, high pressure pump, stage 2 progressive pump controller for MAF systems (also works with MAP's and standalones), 1 625cc/min nozzle, 4 375cc/min nozzles (setup I had installed but never ran meth through), 1 225cc/min nozzle, 4 or 5 50cc/min nozzle( 4 of them are devil's own), 4 snow performance nozzle holders, 4 or 5 devil's own low profile nozzle holders, 2 anti drain solenoids, and around 25 feet of line..
I'm sure if you were to piece it together it would probably cost close to $1000 but I'm willing to let it go for $500..
Here are pictures of the 375cc/min nozzles with snow performance nozzle holders.. no meth has been run through them..
http://i.imgur.com/aS30gMC.jpg
I have a set of precision 1000cc injectors.. I got them cleaned and flow benched about 1000 miles ago... Will come with pigtails.. $255 shipped OBO
http://i.imgur.com/uUHslHEl.jpg
http://i.imgur.com/t5Ii1jf.jpg
s13 cylinder head with intact valve cover, s13 intake cam, set of s14 intake and exhaust cams $100:
http://i.imgur.com/0UkNJgq.jpg
http://i.imgur.com/Mx3zCn0.jpg
Full stock intake manifold with blocked egt port.. $40
http://i.imgur.com/HrlTN0f.jpg
AC compressor and Alternator - $20 each..
http://i.imgur.com/0x9vH7I.jpg
Stock pistons and rods.. The stuff that look like chips on the pistons is just oil absorbent.. the pistons and rods are in great condition -$40
http://i.imgur.com/s8rcYOI.jpghttp://i.imgur.com/91pVXwM.jpg
if you need anything else from the engine let me know..
I can be reached at 609 four five six 9773 I prefer text but will take calls on the weekend..