R33 GTS25T M-sport/R34 GTT Front brake calipers/rotors

[OutToWinPAHC]

SOLD, thanks for looking

[slider2828]

I am interested, but where would I get a replacement rotor for this thing?

[OutToWinPAHC]

They are a pain to get, I had to get mine out of the UK when I replaced them last may after I got the car tuned. Conceptua tuning or from a dealer in the UK, AU, or Japan. UK is the cheapest place TBH.

[EvilRB]

actually you can use Q45 rotors from what I've heard, I have the same R33 type M set up on my Cefiro but I went the easier route and just bought brake adapters to run 350z track rotors for better stopping power and they make a big difference

http://zilvia.net/f/tech-talk/246526-rotors-r33-gtst-calipers.html

[Renelovesnike]

Post a picture of the calipers ears where they mount to the knuckle!

id honestly just order DBA rotors to replace the oem r33/34 ones once the rotors reach there min thicknes.

[slider2828]

From my research you just need to drill out the knuckle a little and you will fit fine...

DBA rotors @ $250 a set and shipping from aussie... I dunno... I run the track a lot, so I sometimes change it before it even gets to min thickness

[OutToWinPAHC]

Q45 rotors work but they are 296x28mm

[dluevanos01]

Any pics yet? I'm interested.

[dluevanos01]

OP: any pictures yet?

actually you can use Q45 rotors from what I've heard, I have the same R33 type M set up on my Cefiro but I went the easier route and just bought brake adapters to run 350z track rotors for better stopping power and they make a big difference

http://zilvia.net/f/tech-talk/246526-rotors-r33-gtst-calipers.html

So the adapter to run 350z track rotors would be the same as the one to used them with Z32 brakes?

[OutToWinPAHC]

http://i32.photobucket.com/albums/d47/outtowinpahc/sale/DSCF4533_zps7eb18c53.jpg
http://i32.photobucket.com/albums/d47/outtowinpahc/sale/DSCF4534_zps82004ae6.jpg
http://i32.photobucket.com/albums/d47/outtowinpahc/sale/DSCF4535_zpsa2632373.jpg
http://i32.photobucket.com/albums/d47/outtowinpahc/sale/DSCF4536_zpsabc16a27.jpg
http://i32.photobucket.com/albums/d47/outtowinpahc/sale/DSCF4537_zps3cb0c547.jpg
http://i32.photobucket.com/albums/d47/outtowinpahc/sale/DSCF4538_zpsf7d605a4.jpg

[OutToWinPAHC]

OP: any pictures yet?



So the adapter to run 350z track rotors would be the same as the one to used them with Z32 brakes?


No they would not work. The mounting point are longer to accommodate 296mm vs the 280. They all use the same pad (z32,r32 GTR or GTST,r33 GTS25T or M, r34 Gtt and the same rebuild kits. Knuckle spacing should be the same and I can verify this once my S chassis evo brembo brackets hit my door step.

[slider2828]

Thanks for all your help.... Would have loved to run this setup, but the rotors would just get too expensive to swap every couple of track days when they over heat.

[OutToWinPAHC]

No sweat, just looking to make room

[BoostinIX]

DBA's site shows a listing. Think it's DBA 4963 for front rotors. DBA-USA or any DBA vendor should be able to get them. (DBA Australia site used for lookup)

[OutToWinPAHC]

You can find rotors on ebay all day too if you want to go that route

[OutToWinPAHC]

Pulled the front drivers caliper to compare it to the 240sx brembo bracket adapters I picked up and the bolt hole thread pitch, size and spacing are identical. 100% will bolt on to an Z or S chassis. I'll snap a few more pictures tomorrow the other pics are crappy and dont show the rotor well.