Bumnah
02-27-2013, 01:16 PM
Oil cooler:
Used for less than 500 miles.
Tomei Oil block for SR20 - NEW
Custom BMRS lines -10 lines tested at 300 psi
TRU-Cool 8x11x1-1/2" oil cooler
Canton Mecca racing remote oil filter
CUSTOM Carbon fiber ducting with dual 3" inlets.
Notes: The system was designed to minimize oil lines as much as possible to reduce the strain on the oil pump. This is a very complete setup! This can go in either S13 or S14. This is a custom setup, so there will be come custom work required for you to install it. Buyer be warned.
S13 Chuki bumper intakes:
Custom intake for the later model s13 front bumper.
Bolt these to the oem intakes ducts on the bumper, and run the hoses to an oil cooler or your brakes, or anything else.
These can used in any application you can think of. The material they are made of is similar to nylon 6. They were made on a selective laser sintering machine.
Here is a video of a laser sintering machine:
Laser Sintering Process (SLS) - YouTube (http://youtu.be/SVkUwqzjGJY)
Each intake has two 3" outlets. You can run each 3" outlet to whatever you like. There is a center line dividing the 3" outlets. There is also a line running around the out side of the intake to help keep the hoses attached. Quality, one off piece. Cost of manufacturing an item like this is significantly higher than the sale price. This is for a pair of intakes, so you get it for both the left and right side. One side was created, and then mirrored for the opposite side. Never used, never tested, no warranty expressed or implied.
Pictures:
http://bumnah.com/cooler/01fullkit.jpg
Full oil cooler kit with optional intake ducts.
http://bumnah.com/cooler/02assembled.jpg
Full kit assembled. Tomei oil block not pictured, but included. Intake ducts are optional
http://bumnah.com/cooler/03cooler.jpg
Back of the heat exchanger, with CF duct mounted.
http://bumnah.com/cooler/05installed.jpg
Kit installed.
http://bumnah.com/cooler/06coolerin.jpg
How the heat exchanger sits.
http://bumnah.com/cooler/07filter.jpg
Close up of the filter mounted.
http://bumnah.com/cooler/08cfduct.jpg
Mounting the CF duct to the heat exchanger.
http://bumnah.com/cooler/09cfduct.jpg
CF duct on the exchanger.
http://www.bumnah.com/ducts/intake01.jpg
How they're mounted.
http://www.bumnah.com/ducts/intake02.jpg
Another angle
http://www.bumnah.com/ducts/intake03.jpg
Yet another angle
http://www.bumnah.com/ducts/intake04.jpg
From the back.
http://www.bumnah.com/ducts/intake05.jpg
Sweet ass graphics!
http://www.bumnah.com/ducts/intake06.jpg
The pair for sale.
PRICING:
Oil cooler kit with intake ducts, $500 shipped in the 48 states.
Oil cooler kit without intake ducts, $400 shipped in the 48 states.
NOTE: CF duct comes with the heat exchange regardless.
Email is the best way to reach me. forums at bumnah dot com
Shipped within 24 hours of payment.
Used for less than 500 miles.
Tomei Oil block for SR20 - NEW
Custom BMRS lines -10 lines tested at 300 psi
TRU-Cool 8x11x1-1/2" oil cooler
Canton Mecca racing remote oil filter
CUSTOM Carbon fiber ducting with dual 3" inlets.
Notes: The system was designed to minimize oil lines as much as possible to reduce the strain on the oil pump. This is a very complete setup! This can go in either S13 or S14. This is a custom setup, so there will be come custom work required for you to install it. Buyer be warned.
S13 Chuki bumper intakes:
Custom intake for the later model s13 front bumper.
Bolt these to the oem intakes ducts on the bumper, and run the hoses to an oil cooler or your brakes, or anything else.
These can used in any application you can think of. The material they are made of is similar to nylon 6. They were made on a selective laser sintering machine.
Here is a video of a laser sintering machine:
Laser Sintering Process (SLS) - YouTube (http://youtu.be/SVkUwqzjGJY)
Each intake has two 3" outlets. You can run each 3" outlet to whatever you like. There is a center line dividing the 3" outlets. There is also a line running around the out side of the intake to help keep the hoses attached. Quality, one off piece. Cost of manufacturing an item like this is significantly higher than the sale price. This is for a pair of intakes, so you get it for both the left and right side. One side was created, and then mirrored for the opposite side. Never used, never tested, no warranty expressed or implied.
Pictures:
http://bumnah.com/cooler/01fullkit.jpg
Full oil cooler kit with optional intake ducts.
http://bumnah.com/cooler/02assembled.jpg
Full kit assembled. Tomei oil block not pictured, but included. Intake ducts are optional
http://bumnah.com/cooler/03cooler.jpg
Back of the heat exchanger, with CF duct mounted.
http://bumnah.com/cooler/05installed.jpg
Kit installed.
http://bumnah.com/cooler/06coolerin.jpg
How the heat exchanger sits.
http://bumnah.com/cooler/07filter.jpg
Close up of the filter mounted.
http://bumnah.com/cooler/08cfduct.jpg
Mounting the CF duct to the heat exchanger.
http://bumnah.com/cooler/09cfduct.jpg
CF duct on the exchanger.
http://www.bumnah.com/ducts/intake01.jpg
How they're mounted.
http://www.bumnah.com/ducts/intake02.jpg
Another angle
http://www.bumnah.com/ducts/intake03.jpg
Yet another angle
http://www.bumnah.com/ducts/intake04.jpg
From the back.
http://www.bumnah.com/ducts/intake05.jpg
Sweet ass graphics!
http://www.bumnah.com/ducts/intake06.jpg
The pair for sale.
PRICING:
Oil cooler kit with intake ducts, $500 shipped in the 48 states.
Oil cooler kit without intake ducts, $400 shipped in the 48 states.
NOTE: CF duct comes with the heat exchange regardless.
Email is the best way to reach me. forums at bumnah dot com
Shipped within 24 hours of payment.