fuel rail alignment problem

[HipHopHippo]

No matter how hard I try I cannot get my fuel rail to go on right. It used to fit fine and then I removed it so I could replace the cushions, and now it is not even close to going on right. The closest I've been to right is having them all off center and then leaving a gap, but then the engine stalls if you leave it in idle. What do I need to replace?
http://www.imgur.com/AXW9i.jpeg
http://www.imgur.com/vcL9p.jpeg
http://www.imgur.com/qtL2j.jpeg
http://www.imgur.com/jwqUv.jpeg

[Biggamehit]

you are missing the plastic insulator that goes under the rail... and odds are that you bent the fuel rail.. I have done it before.

[JFoxx]

first step make the pictures smaller so we can see the whole image..... and if your using a greddy style manifold you know you have to slot the last hole to get it to fit anyhow right? with your old seats the slot was probly fine because they were worn, now you may have to adjust it.... or your rail could just be bent....

[brndck]

also, because freddy manifold.

[HipHopHippo]

first step make the pictures smaller so we can see the whole image..... and if your using a greddy style manifold you know you have to slot the last hole to get it to fit anyhow right? with your old seats the slot was probly fine because they were worn, now you may have to adjust it.... or your rail could just be bent....

Its an Isis manifold, and what do you mean by slotting it?

[HipHopHippo]

Also, would a top feed rail help at all?

[HipHopHippo]

first step make the pictures smaller so we can see the whole image..... and if your using a greddy style manifold you know you have to slot the last hole to get it to fit anyhow right? with your old seats the slot was probly fine because they were worn, now you may have to adjust it.... or your rail could just be bent....

Could the gaps that are in between the fuel injectors and the cushions cause a vacuum leak and make the car stall? It turns on and stays on if you keep you give it gas, but it wont idle

[HipHopHippo]

messagelength

[brndck]

did you seriously copy my avatar pic?

wow.

[Teddy]

messagelength

did you seriously copy my avatar pic?

wow.

Hey man not cool. Don't copy other peoples' avatars.

[HipHopHippo]

did you seriously copy my avatar pic?

wow.

If you don't have anything constructive to say, then I don't want to hear it

[brndck]

hahahahaha you're a genius. can we be friends and dress the same and hold hands and hug in public???
http://24.media.tumblr.com/tumblr_lxne9sYtxB1qk4o4zo1_500.png

[Teddy]

Haha!

But seriously. Cut it out.

[s14boy]

those dont look oem either what brand are they? maybe that is causing a problem of fitment.

[Mikester]

Check my post in your OTHER THREAD ABOUT THE VERY SAME THING: http://zilvia.net/f/engine-tech/498593-fuel-rail-alignment-problem.html

[HipHopHippo]

Check my post in your OTHER THREAD ABOUT THE VERY SAME THING: http://zilvia.net/f/engine-tech/498593-fuel-rail-alignment-problem.html

sorry i made that thread in the wrong location by accident, and what did you do with the third tab thats inbetween the other two?

[HipHopHippo]

Ok so, now it idles for a little bit, and eventually it will bog down, almost die, turn back on, and then die. Also, my temperature gauge needle doesn't move.

[Mikester]

sorry i made that thread in the wrong location by accident, and what did you do with the third tab thats inbetween the other two?

As you saw in the pic, I have an aftermarket rail... So I didn't connect the 3rd tab. On a stock rail; just do the same- dont connect it b/c there is nothing to connect it to.

[HipHopHippo]

As you saw in the pic, I have an aftermarket rail... So I didn't connect the 3rd tab. On a stock rail; just do the same- dont connect it b/c there is nothing to connect it to.

That's a circuit sports rail, right? And how tall areb the spacers you are using?

[Mikester]

I have no idea how tall the spacers are. I used the harware from the stock mani/rail...

Get 2 of these and you will be set: Nissan Genuine OEM S13 SR20DET/ KA24DE Fuel Rail Spacer (http://www.frsport.com/Nissan-Genuine-OEM-S13-SR20DET--KA24DE-Fuel-Rail-Spacer_p_12787.html)

[dopplganger1]

I can see that it is bent in the second picture. and I don't know what that guy up there is talking about slotting the holes for greddy manifolds I bought mine and installed mine with no problems

[STR8E180]

sure your picture isnt big enough mate?

[HipHopHippo]

sure your picture isnt big enough mate?

you want it bigger?

[HipHopHippo]

I can see that it is bent in the second picture. and I don't know what that guy up there is talking about slotting the holes for greddy manifolds I bought mine and installed mine with no problems

This isnt the case with mine, its almost like my fuel rail is too long

[Mikester]

I don't know what that guy up there is talking about slotting the holes for greddy manifolds I bought mine and installed mine with no problems

I'm sure the GReddys fit fit rails like champs. The ISIS and many other knockoffs do not.

[2.5T_/<ouki]

WOW!!! He copied your avatar and your signature

[HipHopHippo]

WOW!!! He copied your avatar and your signature

I liked it so I copied it

[brndck]

Haha!

But seriously. Cut it out.

Check my post in your OTHER THREAD ABOUT THE VERY SAME THING: http://zilvia.net/f/engine-tech/498593-fuel-rail-alignment-problem.html

WOW!!! He copied your avatar and your signature

I liked it so I copied it

imitation is the sincerest form of flattery (even if it does come from an idiot who can't figure out why his knockoff parts don't fit right and keeps making redundant threads)

[HipHopHippo]

imitation is the sincerest form of flattery (even if it does come from an idiot who can't figure out why his knockoff parts don't fit right and keeps making redundant threads)

It was actually the previous owner that put in this part