All items sold

[ghudson]

Okay I have a nearly full RB25 to partout. Some items were off my old coupe that got wrecked including the fender tubs, q45 thottle body, and freddy manifold but they are all OK. Here's the list:

SOLD $550- RB25 transmission w/ shifter. Never ran it but these guys are known to be really strong. 300zx trans not for sale !!!! Nor is the rb26 bellhousing!!!! Will sell the vg30dett bellhousing though!!! pm me

LOWERED $$180 shipped $250- Wiseco pistons 87mm (.040'' over). Typical skirt wear. New rings are $25 each so 250+150=400 and you have a forged piston setup. Rb25 rods come with for free!

LOWERED $$120 SHIPPED $150 Mines ecu, mines is currently contacting me back about the ecu and I will inform all when I know.

PENDING $90 Stock RB25 s1 ecu 5spd

LOWERED $80 SHIPPED $100 ARP RB25 headstuds w/ nuts and washers

$50 RB25 valve covers (white)

$80 Rb25 valve covers, coilpack cover, timing covers (upper and lower), and timing cover back plate

BOTH SOLD $10 each (2) timing cover back plates

LOWERED $$230 SHIPPED $250 RB25 cylinder head, no warpage, cam journals lightly scored, very minimal, comes with cams.

LOWERED $$120 PICKUP $150 RB25 block bored 87mm (0.040'') with main carriage and oil quirters and pickup tube.

SOLD $150 Freddy manifold, mounting holes where fuel rail bolts down were broken off in wreck but I had my welder re-tig weld them on and the fuel rail bolts nice and snug now :) also one hole where the throttle body mounts is stripped, just needs a heli-coil

SOLD $120 Ebay SS topmount manifold, T3 flange, 2-bolt 38mm gate flange

LOWERED $$75 SHIPPED $80 Q45 throttle body w/tps sensor, was in wreck just bent the throttle cable swivel but I bent her back and she functions properly now! All cruise related items are stripped off of it also.

1 SOLD 1 LEFT $40 RB25 oil pumps

LOWERED $$50 SHIPPED $80 Rb25 s1 coilpacks w/ignitor

$120 S13 Fender tubs premade, torched out of old s13 coupe. Will save someone alot of money and time. Just clean them up and weld them in.

SOLD $200 Holset hx30, welded gate for an external gate setup. Some side to side shaft play, no fore and aft play. Can send more pics just lmk

SOLD $120 T28 with downpipe and all lines, no shaft play at all.

SOLD $80 s13 crossmember for and rb25 swap. Somebody welded thick steel plates on it to hold the factory rb25 mounts (which I have)

Plenty of other rb25 s1 and s2 goodies just post a reply asking for things! -PS PUMP SOLD...

http://imageshack.us/a/img812/7393/imag0371bh.jpg (http://imageshack.us/photo/my-images/812/imag0371bh.jpg/)

Uploaded with ImageShack.us (http://imageshack.us)

http://imageshack.us/a/img526/2807/imag0372h.jpg (http://imageshack.us/photo/my-images/526/imag0372h.jpg/)

Uploaded with ImageShack.us (http://imageshack.us)

http://imageshack.us/a/img252/9012/imag0373h.jpg (http://imageshack.us/photo/my-images/252/imag0373h.jpg/)

Uploaded with ImageShack.us (http://imageshack.us)

http://imageshack.us/a/img542/3489/imag0374g.jpg (http://imageshack.us/photo/my-images/542/imag0374g.jpg/)

Uploaded with ImageShack.us (http://imageshack.us)

http://imageshack.us/a/img407/5681/imag0375u.jpg (http://imageshack.us/photo/my-images/407/imag0375u.jpg/)

Uploaded with ImageShack.us (http://imageshack.us)

http://imageshack.us/a/img829/1831/imag0376k.jpg (http://imageshack.us/photo/my-images/829/imag0376k.jpg/)

Uploaded with ImageShack.us (http://imageshack.us)

http://imageshack.us/a/img189/2770/imag0377x.jpg (http://imageshack.us/photo/my-images/189/imag0377x.jpg/)

Uploaded with ImageShack.us (http://imageshack.us)

http://imageshack.us/a/img339/4628/imag0378y.jpg (http://imageshack.us/photo/my-images/339/imag0378y.jpg/)

Uploaded with ImageShack.us (http://imageshack.us)

http://imageshack.us/a/img831/9548/imag0379hq.jpg (http://imageshack.us/photo/my-images/831/imag0379hq.jpg/)

Uploaded with ImageShack.us (http://imageshack.us)

[Memberofthe600hpkaclub]

How much for that tranny shipped to 32583...I can also do a business if its any cheaper

[ghudson]

How much for that tranny shipped to 32583...I can also do a business if its any cheaper

You've been pm'd ;)

[Mi BEAN]

Good rb25 oil pan anywhere?

[TATE843]

BUMP FOR LEGIT SHIT! gains you owe me

[dcreech0]

Might be interested in the freddy manifold. can we have better pictures of the damage and fix? Do you happen to have anything else that bolts to the manifold such as the IACV?

[omgRWDgoodness!]

Do you have a throttle cable bracket?

[ghudson]

Might be interested in the freddy manifold. can we have better pictures of the damage and fix? Do you happen to have anything else that bolts to the manifold such as the IACV?

I have iavc, air regulator, mainly all of that stuff. here is some pics

http://imageshack.us/a/img843/7505/imag0178yw.jpg (http://imageshack.us/photo/my-images/843/imag0178yw.jpg/)
Uploaded with ImageShack.us (http://imageshack.us)

http://imageshack.us/a/img26/9885/imag0179zf.jpg (http://imageshack.us/photo/my-images/26/imag0179zf.jpg/)
Uploaded with ImageShack.us (http://imageshack.us)

Here is what the tubs were in if anyone is interested how they look in car:

http://imageshack.us/a/img840/7763/20110927171225.jpg (http://imageshack.us/photo/my-images/840/20110927171225.jpg/)
Uploaded with ImageShack.us (http://imageshack.us)

[ghudson]

Do you have a throttle cable bracket?
Not really, im keeping my nice one for my greddy manifold...

[ghudson]

MINES ECU UPDATE!!!!!

The VX-ROM in the picture is for a manual transmission early version ECR33 Skyline GTS-25t(2WD).

Fuel mapping and ignition timing optimized
Speed limiter cut
Rev limit +500 from stock
With use of aftermarket boost controller set up to 0.85kg/cm2 MAX
Written to accommodate the stock type air cleaner and is not capable of handling the bare/mushroom type air cleaner
Written for use with 100 ron octane rated fuel.

[bkt808]

do you still have the air regulator? the sensor on the water tube below the manifold

[preston240sx]

Is that the stock Rb25 turbo ? If so ill take it tonight

[vroom_vroom]

MINES ECU UPDATE!!!!!

The VX-ROM in the picture is for a manual transmission early version ECR33 Skyline GTS-25t(2WD).

Fuel mapping and ignition timing optimized
Speed limiter cut
Rev limit +500 from stock
With use of aftermarket boost controller set up to 0.85kg/cm2 MAX
Written to accommodate the stock type air cleaner and is not capable of handling the bare/mushroom type air cleaner
Written for use with 100 ron octane rated fuel.

still have the ecu? also would you happen to have the power steering pump?

[ghudson]

Is that the stock Rb25 turbo ? If so ill take it tonight
Yes, I have had others asking for close up pics but if you have paypal ready its yours... Its in great condition. Sorry guys money talks. Ill pm you my paypal address.

[ghudson]

still have the ecu? also would you happen to have the power steering pump?
I have both of those items. Ill pm you a qoute

[ghudson]

do you still have the air regulator? the sensor on the water tube below the manifold
yes but that sells with the manifold sorry...

[drumminnothummin]

Good oil pan??

[rbfunz]

how much for the turbo mani and holset together shipped 85364 thanks

[EjMalernee]

Do you have the power steering pump?

[ghudson]

Do you have the power steering pump?
just sold it

[ghudson]

Good oil pan??
keeping both pans as of now, ill let you know if not...

[ghost_silvia]

Would you take $120 shipped for the tubbs?

[ghudson]

Would you take $120 shipped for the tubbs?
shipping is $43.xx to texas area via ups. So $150 shipped and the tubs are yours, let me know via pm -ghudson

[240dream]

holset shipped to 06360

[ricekiller]

did you sell the stock rb25 turbo?

[ghudson]

did you sell the stock rb25 turbo?
yep sorry. I have 2 friends going topmount though so ill keep all informed when they get to the point of selling theirs...

[Veryflush]

Specs on the holset...vband ?

Sent from my DROID BIONIC using Tapatalk 2

[ghudson]

HOLSET SPECS: (since everyone is asking)

T3 exhaust flange, undivided, It does not state anywhere online or on the housing the A/R but if I had to guess around a 0.60 A/R
Compressor wheel- Inducer: 40.20mm Exducer: 69.00mm
Turbine wheel- Inducer: 65.50mm Exducer: 52.00mm
Oil feed/Oil drain

Welded internal gate, so its setup for an external gate
Some side to side shaft play. Totally runnable and safe. Will put some pics up here when I get home for sure!!

[ghudson]

http://i47.tinypic.com/10zqmc4.jpg

[97nismo]

good parts.....glws

are you still staying rb

[vroom_vroom]

bump for a good seller

[silviadrag]

I might b interested in the tubs best price ship? What kind of power could a hx30 handle?

[Carl H]

damn skippy that trans is sold!

[mkhoid]

still got the S1 ECU, also would you happen to have a snap ring to lock down the shifter ?

text me 240 595 8150

[ghudson]

still got the S1 ECU, also would you happen to have a snap ring to lock down the shifter ?

text me 240 595 8150

Carl got the snap ring along with the trans^ sorry

[ghudson]

I might b interested in the tubs best price ship? What kind of power could a hx30 handle?

I can do 120/130 shipped for the tubs best price. It all depends on where the tubs are going. I'm gonna eat about 30/40 bucks in shipping...

[ghudson]

I can do 120/130 shipped for the tubs best price. It all depends on where the tubs are going. I'm gonna eat about 30/40 bucks in shipping...

Holset hx30 should do around 350hp safely, just my guess.

[efaustin]

price on rb25 oil pan shipped to 43055 pm me

[bkt808]

do you have the o2 sensor if so how much shipped to 96793?

[ghudson]

lowered prices, get it gone!!

[MiamiZ33]

Still got those tubs?

[ghudson]

yes i have them still

[driftlife.son]

ahhhhhhhhh clear ur PM's lol i want that ecu

[rbsilvias13]

Hey I want that head! Says your inbox is full. Let me know what's up with it. Thanks.

[StryfeS13]

The S13 fender tubs, I want them. PM me.

I will gladly send you the $150 shipped for those.

[smokin18]

ill take the tubs and im in georgia.

[s13mikesr20]

Pm me about tubs please

[240sx1234]

your inbox is full, but I am wondering if you have the factory rb25 turbo compressor outlet elbow,the three bolt elbow leading to the intercooler?let me know by pm, thanks

[rbfunz]

if you still have the mines ecu how much shipped to 85364

[[email protected]]

Money sent for headstuds, coilpacks and igniter

[slideslidegnarslide]

Want to sell me the dust plate in between engine and trans?

Need a few other small items as well

[2sav]

do you have cam studs for sale?

[SR.20]

Pmd you yesterday

[jssilc]

hey do you have aac valve its the 3 bolt valve that goes under the manifold and interested in the fuel rail

[blackychan656]

what is still for sale p.m. please

[JBotch79]

Hey, how good did the ebay manifold fit with the holset?

[JamzVik]

You don't happen to have a good power steering pump do you??

[dgrip]

rb25 power steering pump bracket?

[JamzVik]

rb25 power steering pump bracket?

No, I'm needing the pump itself. Mine is taking a crap..

[chiboy002]

do you have a stock rb25 clutch fan?

[MADMIKE]

Does the Hx30 has a 10cm housing? Would you part ways with just the turbine housing

[teddyjr]

I'm in need of the water tube between the block and turbo. It's part number 14499-73L00 and is the one that's a hard line with banjos on either end (one big, one smaller) and a one hole bracket to 33703. - Teddy

[LMFC]

Do you have rb25 cams?

Sent from my SCH-I605 using Tapatalk 2

[supersayianjim]

interested in your head!!

[Mrpopo]

I'm interested in the cylinder head and possibly the pistons too, and I'm right down 85 in GA. PM me please, your inbox says full

[frost1988]

80 shipped?

[RN4URLife]

still have the cylinder head?

[Napolean03]

interested in pistons, will hit you up tomorrow on pm, are they all good, undamaged ringlands etc?

[Zed Nismo]

interested in Crossmember
How much shipped to 95337

[ghudson]

sorry guys but literally everything is sold. Thread needs to be closed...

[Boss_S14]

Do you still have Power Steering bracket for sale??

[smmsak]

Ill take the whit valve covers and head studs let me know!!!