Zerolift Autolab
09-28-2012, 03:47 PM
Hey Everyone,
ZEROLIFT - RB and JZ Engine Mount Kits in stock ready to ship !
RB ENGINE :
The ZEROLIFT Mount Kit is meant to utilize your 240SX Chassis Subframe as well as Motor Mounts unlike other kits that require you to use a specific isolator style mount. This will allow you to expand into solid aftermarket mounts for racing purposes or if you prefer to keep the softer feel you may reuse the stock 240sx motor mounts.
These mounts have gone through a recent Re-design. There have been a hand full of upgrades added to the mounts.
Our Version 2 Mounts are produced from a thicker gauge steel, laser cut, break bent, and Tig Welded.
We recommend replacing your original motor mounts with doing the installation.
Quite often the old mounts are collapsed or blown out.
We recommend the Nismo Motor Mounts or other equivalent mounts for a street car.
With a Race Application there are many quality mounts available - we have used the Avid Racing mounts in the past with good results.
The Mounts are Lifetime Warranted against manufacturing flaws I.E. Welds Breaking, Bends Warping BUT are NOT Warranted against Rust or Corrosion caused by wear and tear or the weather.
We have had numerous customers use these in high horsepower applications without any issues. With the re-design these ought to handle anything you can throw at them !
Engine Placement with the Zerolift mounts.
The engine sits a bit farther back and slightly higher than most of the other
kits on the market. We positioned the engine slightly higher to protect the oil pan from bottoming out, while maintaining proper hood clearance even while using the OEM over the top intake manifold.
The Front Sway bar to Oil pan clearance leaves you plenty of room to run an increased diameter aftermarket sway bar.
On the Firewall there is a small amount of clearancing needed for the Starter on the Right Hand Side of the Tunnel.
The Installation of the mount kit is fairly simple, they consist of 2x Subframe Brackets 2x Engine Brackets 1x Transmission Bracket.
The Mounts are finished in a Satin Bronze Powder Coat.
Mount Kit pricing is $250.
Shipping per kit is approximately $10 within the USA Lower 48 states.
We can also help you with a Driveshaft for your conversion if you are interested.
Steel - Chromoly - or Aluminum are all available.
RB ENGINE KIT :
http://i251.photobucket.com/albums/gg308/Zerolift-Auto/RB%20-%20JZ%20Mount%20Set/2.jpg
==========================================
JZ ENGINE
The ZEROLIFT JZ Mount Kit is meant to utilize your 240SX Chassis Subframe as well as Motor Mounts unlike other kits that require you to use a specific isolator stylemount. This will allow you to expand into solid aftermarket mounts for racing purposes or if you prefer to keep the softer feel you may reuse the stock 240sx motor mounts.
The mounts are made of 3/16” Steel that has been Laser Cut, Brake Bent, and Welded.
The Mounts are Lifetime Warranted against manufacturing flaws I.E. Welds Breaking, Bends Warping BUT are NOT Warranted against Rust or Corrosion caused by wear and tear or the weather.
The mount kit is compatible for S13 / S14 / S15 and 1JZGTE, 1JZGTE VVTI, 2JZGTE, and 2JZGTE VVTI... Also compatible with the Non Turbo Blocks.
We have had numerous customers use these in high horsepower applications without any issues.
The Mounts are powder coated Bronze.
The JZ Mount kit pricing is $350 shipped
We can also help you with a Driveshaft for your conversion if you are interested.*
Steel - Chromoly - or Aluminum are all available.*
JZ ENGINE KIT :
http://i251.photobucket.com/albums/gg308/Zerolift-Auto/RB%20-%20JZ%20Mount%20Set/JZKit2.jpg
Zerolift Built S13 with RB26 -
GT42 Supra vs. RB26 240sx - YouTube (http://youtu.be/sx7cR4AvQIU)
Most Recent 2JZ Project at Zerolift -
Using the Zerolift Mount Kit and the Zerolift 3.5" Aluminum Driveshaft
http://i251.photobucket.com/albums/gg308/Zerolift-Auto/RB%20-%20JZ%20Mount%20Set/2JZS13.jpg
Please let us know what we can help with.
Thank you
ZEROLIFT - RB and JZ Engine Mount Kits in stock ready to ship !
RB ENGINE :
The ZEROLIFT Mount Kit is meant to utilize your 240SX Chassis Subframe as well as Motor Mounts unlike other kits that require you to use a specific isolator style mount. This will allow you to expand into solid aftermarket mounts for racing purposes or if you prefer to keep the softer feel you may reuse the stock 240sx motor mounts.
These mounts have gone through a recent Re-design. There have been a hand full of upgrades added to the mounts.
Our Version 2 Mounts are produced from a thicker gauge steel, laser cut, break bent, and Tig Welded.
We recommend replacing your original motor mounts with doing the installation.
Quite often the old mounts are collapsed or blown out.
We recommend the Nismo Motor Mounts or other equivalent mounts for a street car.
With a Race Application there are many quality mounts available - we have used the Avid Racing mounts in the past with good results.
The Mounts are Lifetime Warranted against manufacturing flaws I.E. Welds Breaking, Bends Warping BUT are NOT Warranted against Rust or Corrosion caused by wear and tear or the weather.
We have had numerous customers use these in high horsepower applications without any issues. With the re-design these ought to handle anything you can throw at them !
Engine Placement with the Zerolift mounts.
The engine sits a bit farther back and slightly higher than most of the other
kits on the market. We positioned the engine slightly higher to protect the oil pan from bottoming out, while maintaining proper hood clearance even while using the OEM over the top intake manifold.
The Front Sway bar to Oil pan clearance leaves you plenty of room to run an increased diameter aftermarket sway bar.
On the Firewall there is a small amount of clearancing needed for the Starter on the Right Hand Side of the Tunnel.
The Installation of the mount kit is fairly simple, they consist of 2x Subframe Brackets 2x Engine Brackets 1x Transmission Bracket.
The Mounts are finished in a Satin Bronze Powder Coat.
Mount Kit pricing is $250.
Shipping per kit is approximately $10 within the USA Lower 48 states.
We can also help you with a Driveshaft for your conversion if you are interested.
Steel - Chromoly - or Aluminum are all available.
RB ENGINE KIT :
http://i251.photobucket.com/albums/gg308/Zerolift-Auto/RB%20-%20JZ%20Mount%20Set/2.jpg
==========================================
JZ ENGINE
The ZEROLIFT JZ Mount Kit is meant to utilize your 240SX Chassis Subframe as well as Motor Mounts unlike other kits that require you to use a specific isolator stylemount. This will allow you to expand into solid aftermarket mounts for racing purposes or if you prefer to keep the softer feel you may reuse the stock 240sx motor mounts.
The mounts are made of 3/16” Steel that has been Laser Cut, Brake Bent, and Welded.
The Mounts are Lifetime Warranted against manufacturing flaws I.E. Welds Breaking, Bends Warping BUT are NOT Warranted against Rust or Corrosion caused by wear and tear or the weather.
The mount kit is compatible for S13 / S14 / S15 and 1JZGTE, 1JZGTE VVTI, 2JZGTE, and 2JZGTE VVTI... Also compatible with the Non Turbo Blocks.
We have had numerous customers use these in high horsepower applications without any issues.
The Mounts are powder coated Bronze.
The JZ Mount kit pricing is $350 shipped
We can also help you with a Driveshaft for your conversion if you are interested.*
Steel - Chromoly - or Aluminum are all available.*
JZ ENGINE KIT :
http://i251.photobucket.com/albums/gg308/Zerolift-Auto/RB%20-%20JZ%20Mount%20Set/JZKit2.jpg
Zerolift Built S13 with RB26 -
GT42 Supra vs. RB26 240sx - YouTube (http://youtu.be/sx7cR4AvQIU)
Most Recent 2JZ Project at Zerolift -
Using the Zerolift Mount Kit and the Zerolift 3.5" Aluminum Driveshaft
http://i251.photobucket.com/albums/gg308/Zerolift-Auto/RB%20-%20JZ%20Mount%20Set/2JZS13.jpg
Please let us know what we can help with.
Thank you