*Rebuilt* 0 miles CA18DET Swap + More CA spare Parts *Pics*

[kabukie]

Hello,

I have a Rebuilt CA18DET, that I no longer have the time nor financial backing to finish the project. Its my loss your gain. Alot of quality parts were used during the build as no expense was spared. I've got 95% of the complete swap for a S13, missing small things like O2 Turbo Housing/Turbo Inlet/misc piping.

Onto the CA18DET swap: Will come with 5spd Transmission,Clutch/Flywheel Driveshaft, SMIC, Piping, Turbo, Complete wiring harness with MAFS and ECU. Along with a 0 Mile CA18DET, which will require a Proper Break-in period.

The following was done to the engine during the rebuild process.


*Block hot-tanked/honed. Head resurfaced. 0mi since build. Rotating assembly
coated with assembly lube during build.
*Stock bore.
*New Mahle Piston rings and Clevite rod and main bearings.
*Cometic ML Headgasket
*ARP Headstuds
*Power Enterprise Timing Belt
*New Timing Belt Tensioner
*New Waterpump
*Re-manufactured Oilpump
*Full new factory gasket set.
*Stainless Steel allen valve cover/cam cover hardware
*Stainless Steel braided oil feed line.
*Rebuilt T-25 with 0mi.
*Bottom mount tubular manifold.
*Turbo water feed block-off.

Everything pictured below will be included with the CA18DET Swap. I am asking $1200 for the complete swap.

http://img.photobucket.com/albums/v644/P_Productions/DSCN1167.jpg

Closer look at the engine
http://img.photobucket.com/albums/v644/P_Productions/DSCN1082.jpg
http://img.photobucket.com/albums/v644/P_Productions/DSCN1083.jpg
http://img.photobucket.com/albums/v644/P_Productions/DSCN1085.jpg
http://img.photobucket.com/albums/v644/P_Productions/DSCN1093.jpg
http://img.photobucket.com/albums/v644/P_Productions/DSCN1089.jpg
http://img.photobucket.com/albums/v644/P_Productions/DSCN1088.jpg

ECU and Wiring Harness and MAFS
http://img.photobucket.com/albums/v644/P_Productions/DSCN1157.jpg
http://img.photobucket.com/albums/v644/P_Productions/DSCN1159.jpg

Everything you get
http://img.photobucket.com/albums/v644/P_Productions/DSCN1167.jpg

[kabukie]

Here are my Extra CA18DET Parts:

http://img.photobucket.com/albums/v644/P_Productions/DSCN1161.jpg

Flywheel $30
Timing Covers $30
Valve Cover $20

http://img.photobucket.com/albums/v644/P_Productions/DSCN1169.jpg

Rear main Seal Holder $10
Coil pack bracket $10
5 speed Transmission brace $25
OEM Cam gears $15 each/ $20 for both
CA18DET Alternator $60
CA18DET Starter $60
CA18DET Power Steering Pump $60

http://img.photobucket.com/albums/v644/P_Productions/DSCN1133.jpg

Coil Packs $15 each
Coil Pack Harness $30

http://img.photobucket.com/albums/v644/P_Productions/DSCN1102.jpg

CA18DET Intake Manifold $60

http://img.photobucket.com/albums/v644/P_Productions/DSCN1103.jpg

CA18DET Rear Transmission Plate $30

http://img.photobucket.com/albums/v644/P_Productions/DSCN1172.jpg

CA18DET Block and Crankshaft and block girdle $150

Also have a Spare CA18DET Transmission in Great shape $150 *Will get pic if interested*

[kabukie]

Bump for the CA18DET. Someone buy it I want my storage clean and ready for winter projects

[KiLLeR2001]

Wish I had infinite money. This would be the perfect candidate for my two-tone. :(

[Lumos]

Oh man this is just what I need. How much for the long block with intake manifold and transmission, but minus exhaust manifold and turbo and harness and ecu and such shipped to 95476? I just blew mine after about 4 loving years with it so if I could just buy the longblock and trans it would be much appreciated.

[kabukie]

Oh man this is just what I need. How much for the long block with intake manifold and transmission, but minus exhaust manifold and turbo and harness and ecu and such shipped to 95476? I just blew mine after about 4 loving years with it so if I could just buy the longblock and trans it would be much appreciated.

I have all of those for sell separately: Short block $150, Intake manifold $60, and transmission $150. I'm not willing to split the CA18DET swap at the moment. Shipping via UPS for all the above is $259.86, if you have another method of shipping you would prefer LMK

[kabukie]

Wish I had infinite money. This would be the perfect candidate for my two-tone. :(


Wish you did too. Pm'ed you a special offer since your in FL and could possibly do local pickup.

[Mofuhcka]

Not a bad deal, just the CA isnt that popular haha. GLWS

[CaDet S13]

I was wondering if you have the vacuum canister and silenoid for the butterfly valves available. Right now im running mine blocked off which leaves them fully open since i dont have those parts and im interested in getting it setup the right way. I heard it increases throttle response quite nicely.

I might also be intersted in the spare block, intake manifold, tranny ans a few other things im located in south florida so i would come pick them up. Lmk via email [email protected] or txt me at 954-815-6568

[deco]

Would you let go of the short block minus the block? Just need the crank caps, girdle crank, and oil squerters, shipped to. 89131. Lmk thanks

[Luvs2slide]

WHat a great price for the motor.

[rangerjavi]

Very good deal also CA's have a pretty big fan base here in Florida don't know what that guy is talking about not being popular.

[Crozier]

Would love to buy just the head. Pm me if you're interested in selling the head

[humilde_s13]

i want ittttttttttttt, if you werent so far i would offer you my running coupe for the swap+help to install motor in my vert.

[Shouldahadav8]

Bump for a trust worthy seller.

[wangan_cruiser]

if only i have money for this for my zenki

[kabukie]

I was wondering if you have the vacuum canister and silenoid for the butterfly valves available. Right now im running mine blocked off which leaves them fully open since i dont have those parts and im interested in getting it setup the right way. I heard it increases throttle response quite nicely.

I might also be intersted in the spare block, intake manifold, tranny ans a few other things im located in south florida so i would come pick them up. Lmk via email [email protected] or txt me at 954-815-6568

I do not have the vaccum canister nor the silenoid. I've sent you a text

[kabukie]

Would you let go of the short block minus the block? Just need the crank caps, girdle crank, and oil squerters, shipped to. 89131. Lmk thanks


I would prefer to sell it together since the block and main caps and crankshaft should go together to the same buyer. But due to the lack of interest and the need for my storage space back, I would be willing to part with them. I could do $215 shipped for the items you asked for. LMK

[kabukie]

Would love to buy just the head. Pm me if you're interested in selling the head

Sorry not willing to part with the head unless I have a confirmed buyer for the block.

[omgwtf]

maybe sell the ecu?

[kabukie]

maybe sell the ecu?


I would prefer keeping the ECU with the swap in case someone wants to buy a complete CA18DET swap.


Also PRICE DROP ON THE ENTIRE CA18DET Swap!!!!

$1250 Picked up!!!! BUY IT!!!!

[humilde_s13]

power steering pump w/ bracket shipped to 23314? pm me

[nismo_200sx]

text me about the power steering pump if humidle doesn't get it. i have cash in hand right now! i need this pump asap!!!! shipped to 81007 cash in hand. lol i just need this baddddddd 719-369-1821

[kabukie]

power steering pump w/ bracket shipped to 23314? pm me

Was sold Locally over the weekend. Sorry.

Everything else is still for sale!

[humilde_s13]

AAHH Shoot ok

[purplove]

Do you have the stock intake pipe? I neeeeeed. pm me.

[kabukie]

Do you have the stock intake pipe? I neeeeeed. pm me.


Thats one of the few things missing from making it a 100% turn key swap. Some 2.5-3 Inch Mandrel Bent piping and you should be able to fabricate a intake pipe.

[kabukie]

No love for the CA18DET????

Any offers? Since apprently I'm asking too much. But "Lowballers" be prepared to be ignored

[humilde_s13]

Waiting if my friend ever finishes rebulding my ca if not ima just buy another

[kabukie]

Waiting if my friend ever finishes rebulding my ca if not ima just buy another

Ok. Just LMK. Mine is ready to go and ready for install. Its also still for sale!

[kabukie]

Accepting Serious/Legit offers! Your chance to get a Great swap for a Bargain!

BUY IT NOW!

[TheKingBLop]

What a deal. This would be killer for my sil80, but like every other zilvian, I'm broke. Glws.

[kabukie]

Price dropped to $1,199!!!
Someone buy it and Enjoy a fresh motor that no one has abused/beat on.

[kabukie]

Also have a SOHC A/C bracket that can be modded to be used with this swap. Included for FREE! Buy this SWAP, its almost A/C Friendly!

http://img.photobucket.com/albums/v644/P_Productions/DSCN1458.jpg

[kabukie]

Bump for a CA18 Swap and CA18 Parts!

[Lumos]

I'd buy just the motor and trans without the exhaust manifold and turbo for 1200 shipped to cali. If you were interested in that.

[kabukie]

I'd buy just the motor and trans without the exhaust manifold and turbo for 1200 shipped to cali. If you were interested in that.

Whats your zip code. I might be able to make that happen.

[Lumos]

it's 95476. That would be awesome if you could.

[kabukie]

it's 95476. That would be awesome if you could.


Best I can do for the Engine and Trans is $1380 shipped to your address. LMK

[240sxmetal]

Ca stuff yay! Haha. I want the block and all but that shipping might cost a ton... PMing sir.

[R4KA240]

How much for backing plate and a/c bracket shipped to 71108?

[kabukie]

How much for backing plate and a/c bracket shipped to 71108?

Shipping would be $22 to your address. So $78 shipped plus Paypal fee would be the total for both parts.
LMK

[R4KA240]

Just found an a/c bracket local. PM me Paypal info and ill go ahead and get that dust plate.

[R4KA240]

PM and payment sent.

[kabukie]

Bump! Still for sale~!

[humilde_s13]

dude txt me ima buy it.

[humilde_s13]

hey man sorry if I keep messaging you, but I will buy this asap being ""serious"". get in contact with me when you can. thanks

[Lumos]

Hey man I finally got that check I was waiting for and I'm readying to buy this thing if you've still got it. What's your paypal info?

[kabukie]

I've been out of town for the past few weeks for work, but I'm back and ready to get this thing out. Everyone who has contacted has been Pm'ed/Texted. Still for sale! 1st come 1st served!

[Future240]

Over the 2 bump limit, you can start a new thread in 3 days.