WanganWizard
02-28-2012, 01:05 AM
Sold my car and dont need to build the rb26 anymore so im selling it. Disassembled at 60,000kms to replace seals and gaskets while it was out, was in perfect working order with 145-150 compression across the board. Below are prices that are OBO but what i feel to be fair, more stuff bought = better deal so dont be afraid to shoot an offer. Everything will be PLUS shipping.
Bare 05U Block, hot tanked,magnafluxed and quick hone painted black,comes with cradle and squirters - $350
OEM R32 crank, should get a collar but clean otherwise,no scoring- SOLD
Polished Valve covers 8/10 condition could use a quick reshine - SOLD
cam covers, coil cover and front timing cover)
Complete RB26 engine harness, uncut - $250
1 complete set of 6 OEM pistons and rods complete with rings, very minimal det on 2 piston tops , have been wire wheeled and cleaned(had good compression but rings should be replaced anyways so im not saying to use them) - $100
1 set of OEM Pistons, and wrist pins - $50
2 Stock GTR Turbos, minimal shaft play, no smoke, semi polished housings and polished wg actuators - $250, can include stock manifolds,elbows aswell
RB26 Y-Pipe for turbos- $50
2 GTR Mafs - pending
3 Cam angle sensors - $70 each (tested working condition)
Rb20/26 ignitor - pending
Greddy clear timing cover, says RB26 on it, one small crack at bottom- $70
OEM Valve seals intake and exhaust - $40
OEM valves, springs, retainers - $100
OEM camshafts - $50 a set, have 2 sets
OEM water pump - $30
Intake plenum assembly, with ITB's and AAC valve - SOLD
Fuel rail - $40
Injector resistor box - $50
GTR rear 6 bolt axles - SOLD
R200 diff - $50
GTR 5 lug hubs, one needs bearing - $50
OMP Universal seat rails, side mount - $50 never used
Blitz intake filters and adaptors - $140
BNIB supertech intake and exhaust valve guides RB26- SOLD
Coilpack harness - Pending
R32 GTST rims, clean no rash repainted gun metal grey with center caps 9/10 condition no tires - $180
GTR front drive shaft - $50
GTR rear drivshaft - $80
Stock RB20 ECU - $90
RB20 polished valve covers and custom vented coilpack cover powdercoated black - $100
RB25 intake OEM intake plenum - $80
RB20 intake plenum OEM- $80
RB26 knock sensors - $50
If you need anything not listed PM me and i may have it. Parts located in Kelowna BC Canada,can accept paypal now!
Bare 05U Block, hot tanked,magnafluxed and quick hone painted black,comes with cradle and squirters - $350
OEM R32 crank, should get a collar but clean otherwise,no scoring- SOLD
Polished Valve covers 8/10 condition could use a quick reshine - SOLD
cam covers, coil cover and front timing cover)
Complete RB26 engine harness, uncut - $250
1 complete set of 6 OEM pistons and rods complete with rings, very minimal det on 2 piston tops , have been wire wheeled and cleaned(had good compression but rings should be replaced anyways so im not saying to use them) - $100
1 set of OEM Pistons, and wrist pins - $50
2 Stock GTR Turbos, minimal shaft play, no smoke, semi polished housings and polished wg actuators - $250, can include stock manifolds,elbows aswell
RB26 Y-Pipe for turbos- $50
2 GTR Mafs - pending
3 Cam angle sensors - $70 each (tested working condition)
Rb20/26 ignitor - pending
Greddy clear timing cover, says RB26 on it, one small crack at bottom- $70
OEM Valve seals intake and exhaust - $40
OEM valves, springs, retainers - $100
OEM camshafts - $50 a set, have 2 sets
OEM water pump - $30
Intake plenum assembly, with ITB's and AAC valve - SOLD
Fuel rail - $40
Injector resistor box - $50
GTR rear 6 bolt axles - SOLD
R200 diff - $50
GTR 5 lug hubs, one needs bearing - $50
OMP Universal seat rails, side mount - $50 never used
Blitz intake filters and adaptors - $140
BNIB supertech intake and exhaust valve guides RB26- SOLD
Coilpack harness - Pending
R32 GTST rims, clean no rash repainted gun metal grey with center caps 9/10 condition no tires - $180
GTR front drive shaft - $50
GTR rear drivshaft - $80
Stock RB20 ECU - $90
RB20 polished valve covers and custom vented coilpack cover powdercoated black - $100
RB25 intake OEM intake plenum - $80
RB20 intake plenum OEM- $80
RB26 knock sensors - $50
If you need anything not listed PM me and i may have it. Parts located in Kelowna BC Canada,can accept paypal now!