CHASE BAYS rb25 to s13 harness

[Tomsd03]

Times are rough and I have to part with it. Asking 600.
http://i1089.photobucket.com/albums/i355/Tommysd3/Partsforsale013.jpg

[RBPOWERED240]

if this was for s14, i would of considered it big time. free bump for ya

[Chase Bays]

Thats a good price.

[Sergio180sx]

does it have all connections?

[Tomsd03]

Thats a good price.
SIGH..... Yes it is, taking a big hit on it, as well as with the project.
does it have all connections?
It comes setup without the air regulator clips. As long as you block off the two hoses that go to it, it will run great with stock ecu. its also set up with a z32 maf. never been used as well.

[mgramata]

bump cause you live in moreno valley also! aha
good luck with the sell. damn good price

[Tomsd03]

any offers?

[P-Funk alot]

damn i want this. pm me your number. do you need a replacement harness for rb25 to s13 lemme know lets see if we can work something out

[Tomsd03]

damn i want this. pm me your number. do you need a replacement harness for rb25 to s13 lemme know lets see if we can work something out

P Funk, you've got mail.

[Tomsd03]

lowered price to 6.

[Tomsd03]

Need this thing gone.

[Tomsd03]

Someone call the fire department cause this deal is smokin!

[conrad_s13.5]

bump for,....dnt know why this hasnt sold yet-ness

[Michaelwinne]

I really want this. Is this for series 1 or 2 RB25? Or does it not even matter?

[Tomsd03]

I really want this. Is this for series 1 or 2 RB25? Or does it not even matter?

Its for series 1. difference would be that series1 has an ingitor chip located on top of the spark plug cover( ChaseBays harness relocates this chip to inside the vehicle next to the ecu) and I believe that the skyline mafs are a little different between s1 and s2. but this harness has a Z32 maf setup. however i would assume this could be converted (repining) to fit the appropriate one or you could contact Chase to get the correct one as the harness is made with the maf being detachable at the harness. As stated above by Chase Bays this harness is at a really good price, they also said that when i had it listed for 650.

[Michaelwinne]

Yea it is a good price for a chase bays. Why would someone go this route instead of one from wiring specialties? That's the one I have been looking at getting.

[Tomsd03]

I went with CB harness cause i wanted to be different from the crowd. when I open my hood I want to show the fact that their was some pride taken in my swap. Didnt want a two inch thick oem style wiring harness running all over my engine bay. The CB harness is F*ckn show quality. This harness is a "tucked" type deal, not spaghetti engine bay.
From the CB website:
"CM1 harness – The CM1 harness features all new commercial grade, high heat, thin jacketing wire (rated from -49° to +257° F), individually striped for easy identification and all new sensor plug pins. It is covered in full flame retardant nylon sleeving (Operating Temperature Range -103° to 257°F; Melt temp 446°F), and adhesive lined heat shrink. All engine harnesses go directly to the ECU clips, and include all the needed wiring and plugs to make the harness plug and play to your vehicle. The harness is built with aesthetics and functionality in mind. Our harnesses have had a lot of R&D done for proper wiring technique, with all shielded wire used where needed. It features a stealthy look but is also easily accessed, keeping the motor easily worked on. This harness is great for someone looking to clean up their engine bay and replace the used and worn down stock harness."
Honestly I was a couple hours away from getting a WS harness, figured id do it after I got home from the Eibach Honda meet. After I saw a couple Cars with CB harnesses I knew THATS what I was doing. After dealing with CB customer service and products, I will always save up a little more to get their product.
It all comes down to what you want out of your car. Wanna get some nice wheels, or keep rockin the steelies?
Im getting rid of it cause I got F*CKED on my swap and need the cash now(SORE SUBJECT)

[Tomsd03]

Tuck:
ImageShack® - Online Photo and Video Hosting (http://imageshack.us/photo/my-images/381/enginebaylds7.jpg/)
Not tucked:
http://i47.tinypic.com/34hjlts.jpg

[Michaelwinne]

That looks really nice man. Yea I have been contemplating a wiring specialties one for $500 so this one is very tempting. I would have to get a Z32 MAF though. If you still have it in a week or two or go even lower in price I will be all over this.

[Tomsd03]

That looks really nice man. Yea I have been contemplating a wiring specialties one for $500 so this one is very tempting. I would have to get a Z32 MAF though. If you still have it in a week or two or go even lower in price I will be all over this.

You've got a PM!

[sleeper108]

I am in the same boat for the price....

could you shoot me a price shipped to 87107?

maybe we can work something out? (I don't want to lowball you, but if you are taking any trades, I could add cash to compensate. Otherwise I'm worried I wont be able to have enough cash)

[specialk2003]

Damn, if this was for a 26, I would be all over this.

[Tomsd03]

Sorry Sleeper harness is sold.