Complete RB20DET w/5spd, Mckinney mounts, KA D/S ++

[GenPac]

Removed the RB20DET in favor of more litres and less snail. I'm looking to get $1500 for everything, but I am willing to deal a bit if it all goes at once.

The RB20DET has had the following replaced with OE parts: Timing set (belt, idler pulley, tensioner pulley), Head gasket, Upper and Lower intake gaskets, Exhaust manifold gasket and manifold studs/nuts/washers, Water pump and thermostat, Cam cover gaskets and grommets... I'm sure I'm leaving some things out.
Other stuff done:
installed ARP headstuds, have a custom heatshield for the turbo/mani and header wrap on the manifold and elbow.
Trans has a Trust shift knob on it because I couldn't get it loose. OEM KA 5spd driveshaft as well, if needed. McKinney basic mounts, ECU, J60 MAF, S13/RB harness, Large 3x11x30 intercooler with RB20 piping, Clutch slave and kevlar clutch line, Downpipe w/WB bung, manual boost controller, ect. I'm sure I am forgetting somethings.

Essentially, it's all there, already refreshed with what's recommended when you buy from an importer. I am not interested in shipping this, at this time!

For now, I'd like to sell complete but might be willing to part out if there's no interest as a single sale.

I can be reached at 702-577-7653, text preferably. Or PMs on here.

PICS:
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20120118_173721.jpg
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20120118_173444.jpg
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20120118_173840.jpg
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20120118_174037.jpg
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20120118_174250.jpg
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20120118_173635.jpg
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20120118_173615.jpg
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20120118_173600.jpg
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20120118_173537.jpg
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20120118_173521.jpg

installed pic:
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20110602_200509.jpg

obligatory car pic:
http://i284.photobucket.com/albums/ll18/rogers98_photos/S13%20vert/IMG_20110602_192809.jpg

[GenPac]

Not really a bump, but I do have a local buyer. As for now this is spoken for.

[rbeast]

just a quick question, i dont mean to jack your thread or anything. how did you mount the fmic? people have told me i'll need to remove the steel bumper reinforcment....

[GenPac]

just a quick question, i dont mean to jack your thread or anything. how did you mount the fmic? people have told me i'll need to remove the steel bumper reinforcment....

That's correct. Remove it or run a much smaller IC.

[Danielmcn]

Or cut into the support a little..

[GenPac]

This is sold. Please close!