PDA

View Full Version : CO S15 sr20det for sale engine only

Koukisr20
10-16-2011, 07:32 PM
I'm selling my s15 sr20det engine only. Six speed has already been sold. It runs great and is basicly stock aside from bolt-ons. I was pretty much givin an ls1 and t56 so I'm swapping that in. I have a bunch of parts that can be sold with the engine or seperatly. I'm asking $1500 for the engine, hks 740cc injectors, tubular turbo manifold and s14 wiring specialties conversion harness.

Besides the engine I have an
Apexi power fc ecu with the map sensor
Blitz intercooler and piping kit with hks ssqv bov
Sard fuel press Reg
Apexi short ram intake and filter
Blitz active system twin plate clutch with about %40 left on the fiber plates
Driveshaft shop aluminum drive shaft
The setup was ready for a bigger turbo and top mount manifold but I never did it.

I'd like to sell all of this in one shot. I'd take $2300 for everything. This is super cheap for all this stuff! I need to sell it so I can finish my ls swap. The engine is still in the car so I can run it for whoever might want it if need be.

I'll try to post pics soon, otherwise pm me with questions
az24tsx
10-16-2011, 08:38 PM
Got a transmission for anyone who buys this and wants a 6spd trans seller glws super good price
SkylinePowas13
10-17-2011, 01:20 AM
Pm me about the driveshaft 6speed into s13 thx
Future_gohan
10-17-2011, 01:30 AM
I want just the motor and wiring harness? pm me a price
Koukisr20
10-17-2011, 12:59 PM
All pm replied
bftII40
10-17-2011, 01:49 PM
how could you run it without a transmission? Pull start?

Edit* pics would also help your "sale"
Koukisr20
10-17-2011, 02:06 PM
You can bolt the starter on with a bolt and nut as long as the clutch is on it, it will start. Thanks for the pull start suggestion though.
Koukisr20
10-30-2011, 09:31 PM
Still for sale. Motivated to sell asap!!
Anon9mouz
10-30-2011, 09:57 PM
Noob? Could that drive shaft work for the ka24de. I have a stock s14 but carrier bearings going out so I wanna get a 1 piece

Sent from my PG86100-EVO3D-using Tapatalk
Koukisr20
10-30-2011, 10:13 PM
Noob? Could that drive shaft work for the ka24de. I have a stock s14 but carrier bearings going out so I wanna get a 1 piece

Sent from my PG86100-EVO3D-using Tapatalk


Nope. Mine is for a six speed trans. It's longer than a 5 speed. Also I'm pretty sure the splines are different between the ka and sr tranny's as well.
Anon9mouz
10-30-2011, 10:39 PM
Nope. Mine is for a six speed trans. It's longer than a 5 speed. Also I'm pretty sure the splines are different between the ka and sr tranny's as well.

Ok thank u hopefully I can find one for a decent price

Sent from my PG86100-EVO3D-using Tapatalk
Koukisr20
11-04-2011, 02:38 PM
Apexi power FC sold!
damnu
11-04-2011, 03:57 PM
pm me price on the hks 740cc?
Koukisr20
11-04-2011, 06:02 PM
pm me price on the hks 740cc?

PM replied
sharpe_corners
11-06-2011, 05:51 AM
Price for clutch shipped to pm inbox. Thanks.