JDM_Tuner
09-03-2011, 08:55 PM
Hey guys I have a 100% full drop in rebuilt Series 2 rb25 swap for any s13. Everything that you need is included to just drop the swap into your s13 and drive it the next day. The engine and tranny had about 80-90k on it before the rebuild.
The swap includes:
RB25DET Full Engine*
(compression is 180 across the board and I have a video of it running)
FrontMountIC
RB25 Tranny w/all sensors, etc.
Aluminum RB25 S13 Conversion Driveshaft
TopHat RB25 S13 Conversion Mounts
RB25 Conversion Crossmember
Wiring SpecialtiesRB25 into S13 Wiring Harnesses
Brand new ACT 6 puck clutch
(also comes with the old clutch that still has some meat on it)
Full S13 Exhaust from Turbo Elbow to Catback.
S13 RB25 Koyo Radiator w/hoses
Walbro Fuel Pump
Boost Gauge
Oil Pressure Gauge
All Hoses and Clamps for Install
New remanufactured rb25 Slave cyl.
Intake filter, maf, and piping
It was rebuilt a few months ago:*
ARP head studs
New OE head gasket
ARP Rod bolts
ACL rod bearings
Head was freshly machined/tested
Also I recently repainted the valve covers, intake side and exhaust side of the engine in wrinkle red/black. It looks like a million bucks!
http://i645.photobucket.com/albums/uu174/JDM_Tuner/2c2ca87f.jpg
http://i645.photobucket.com/albums/uu174/JDM_Tuner/93062ab5.jpg
Over $9,000 was spent on this setup and I am planning on putting it into my s13 but if I can get $6000 for all of it, I'd be okay with letting it go, $3000 less than retail is a crazy great deal. Pm me or Text me directly at 9139409237, I'll hook you up!
The swap includes:
RB25DET Full Engine*
(compression is 180 across the board and I have a video of it running)
FrontMountIC
RB25 Tranny w/all sensors, etc.
Aluminum RB25 S13 Conversion Driveshaft
TopHat RB25 S13 Conversion Mounts
RB25 Conversion Crossmember
Wiring SpecialtiesRB25 into S13 Wiring Harnesses
Brand new ACT 6 puck clutch
(also comes with the old clutch that still has some meat on it)
Full S13 Exhaust from Turbo Elbow to Catback.
S13 RB25 Koyo Radiator w/hoses
Walbro Fuel Pump
Boost Gauge
Oil Pressure Gauge
All Hoses and Clamps for Install
New remanufactured rb25 Slave cyl.
Intake filter, maf, and piping
It was rebuilt a few months ago:*
ARP head studs
New OE head gasket
ARP Rod bolts
ACL rod bearings
Head was freshly machined/tested
Also I recently repainted the valve covers, intake side and exhaust side of the engine in wrinkle red/black. It looks like a million bucks!
http://i645.photobucket.com/albums/uu174/JDM_Tuner/2c2ca87f.jpg
http://i645.photobucket.com/albums/uu174/JDM_Tuner/93062ab5.jpg
Over $9,000 was spent on this setup and I am planning on putting it into my s13 but if I can get $6000 for all of it, I'd be okay with letting it go, $3000 less than retail is a crazy great deal. Pm me or Text me directly at 9139409237, I'll hook you up!