PDA

View Full Version : Arp head stud problems


06-25-2011, 09:56 PM
Ok i have the arp headstuds and have the torque
specs for s14 sr20det but what is the number
sequence to torque them. example front to back
1 9 2 10 3 7 4 8 5 6, or middle starting
5 6 4 8 7 3 10 2 1 9 or
6 5 8 4 3 7 2 10 9 1
that was a example i need the right
number sequence and where can i find.
just one arp head stud, i bent one
dont ask how (i feel embarassed)
any info is great thanks

06-25-2011, 11:02 PM
any and all info on this topic is
good thanks

06-25-2011, 11:02 PM
any and all info on this topic is
good thanks

jr_ss
06-25-2011, 11:35 PM
Dude, you really need to get your hands on an FSM...

But to hand feed you,

Front of cylinder head is at the 7/8 end. Start in the middle and work your way out following that order below...

7 3 1 5 9
8 4 2 6 10

codyace
06-26-2011, 08:27 PM
with that said, also do them in increments of 15 ft lbs to to 75, then 10 more to 85 Use ARP or Moly lube on them.

...you do have an FSM I hope...

s14unimog
06-26-2011, 10:09 PM
Always tighten from the inside out and loosen from the outside in. It's the same sequence for everything in the head.

where can i find.
just one arp head stud, i bent one
dont ask how (i feel embarassed)

do tell please... that's a difficult thing to do there... Just call ARP.

codyace
06-26-2011, 10:19 PM
Always tighten from the inside out and loosen from the outside in. It's the same sequence for everything in the head.

Except the cams ;):ssex:



do tell please... that's a difficult thing to do there... Just call ARP.

I'm curious as to that as well!

yabeet
06-27-2011, 02:05 PM
with that said, also do them in increments of 15 ft lbs to to 75, then 10 more to 85 Use ARP or Moly lube on them.

...you do have an FSM I hope...

ARP says to tighten in 3 increments to 80ft/lbs. I do 27,54 then 80.

s14unimog
06-28-2011, 09:11 AM
Except the cams ;):ssex:


you sure about that...? :kiss:

http://img.photobucket.com/albums/v721/s14unimog/CAMINSTALLATION-SR20.jpg

daryl337
06-28-2011, 09:17 AM
you sure about that...? :kiss:

http://img.photobucket.com/albums/v721/s14unimog/CAMINSTALLATION-SR20.jpg




My FSM states to get the fronts down first, then proceed in the middle->out fashion.


So it goes 9-10-1-2-3-4-5-6-7-8

s14unimog
06-28-2011, 09:53 AM
^that's what it says above. I'm just confirming the sequences for head components. Tighten from the inside out and loosen from the outside in.

codyace
06-28-2011, 02:02 PM
My FSM states to get the fronts down first, then proceed in the middle->out fashion.


So it goes 9-10-1-2-3-4-5-6-7-8

I was trying to make a funny with the 9-10 to start the sequence hehe


ARP says to tighten in 3 increments to 80ft/lbs. I do 27,54 then 80.

I always just did them in my sequence up to 85...unsure why, probably from some oldschool forum 'folklore' (hi Def!) when I first got into these forever ago.

s14unimog
06-28-2011, 02:08 PM
^ damn, we're getting old...