does anyone know how to wire up the euro s14 headlights

[95_S14]

i got euro kouki s14 headlight with the beam leveler in them i have the switch i need for it but i cant find how to wire it up i dont want to wire them and burn out my brandnew light motors i know not alot of people have them working but i want mind to work or i would of just got the jdm ones there the same wiring as the zenki any help would be great thanks

[95_S14]

Anyone ???????

[Future240]

No idea, but found this from searching.

http://zilvia.net/f/chat/249881-s14-zenki-glass-headlights.html

I have an RB25det wireing harness that comes with both a connection for the USDM light and the euro light. I have no clue if the KA or SR harness is any different at all.


In this pic youll see three clip connections. The one on the right (red arrow) is for your USDM light, the one on the left (big circular one w/ no arrow pointing to it) is your high beam. and the unused one on the left (green arrow) is the clip for the glass headlight.
http://i14.photobucket.com/albums/a345/phatsumo82/DSC06105.jpg
Check the wiring that clips into your current lights. If you see another clip thats not being used and is much skinnier (green arrow) than the one thats currently pluged in (red arrow), then its as simple as unplugging the fat clip, replacing the light and plugging in the skinney one into your glass headlights. the fat round clip w no arrow pointing to it fits directly into the glassies.


Good Luck with it

[95_S14]

Thanks but that's not what I'm talking about they euro ones have a aiming motor like newer cars do so you can aim them from the inside of your car

[95_S14]

Anyone out there do this

[95_S14]

Bump from the dead

[mdlesk]

I'm also curious on this as my lights arrived today and I want to wire up the aimer.

Here is the link to the Euro FSM:

http://www.240edge.com/manuals/s14_sr20det.pdf

EL-86 has the wiring diagram. for the switch, but I'm still trying to analyze it.

[JdmGtDriver]

Subscribed...noticed you're in the 909...whereabouts???

[fliprayzin240sx]

There's only one person in my mind that has done this but I doubt he'd chime in since I havent seen him around in a while...ProjectRDM. If you PM him, he'll probably cuss you out...

Actually, after searching for a bit...
http://zilvia.net/f/s-chassis/412587-euro-glass-headlights.html
http://zilvia.net/f/s-chassis/228096-german-zenki-headlights.html

Switch you'd need is the one on the left IIRC.
http://i370.photobucket.com/albums/oo147/eujinchan5/DSC_2156.jpg

[95_S14]

I have the switch and plug for it but what plug do I need for the headlight it's self ?

[iveexcaped3]

You still got your stock kouki

[95_S14]

You still got your stock kouki

Yeah kinda just building my kat setup tryin to get 500 whp and de tune it to 350 for next years redline time attack

[iveexcaped3]

My bad I ment the lights, or does it use the stock lights mounted to the motor?

[mdlesk]

I tried joining SXOC in order to attempt to source the Harness for the Switch and the Headlight motors, but they denied me :( .

Got the following message: Unfortunately your registration at SXOC Bulletin Board did not meet our membership requirements. Therefore your registration was deleted.

I purchased the Switch from the STI as it appears to be the same, just need the harnesses now. If I'm able to source these and get it working, I'll post up a diagram on the wiring, unless someone beats me to it

[msladypaula]

yeah i definitely want to know how to hook these up properly.
I just got my headlights about a week ago.

[59bhp]

if any information is needed my car is a euro kouki (well its a uk s14a)

[KiLLeR2001]

Diagram is actually on EL-66 and EL-67.

The switch itself has 6 wires that need to be hooked up...

1: Red w/blue stripe wire that supplies 12V when the headlights are turned on.
2: Blue w/white stripe output for setting 0
3: Blue w/black stripe output for setting 1
4: Blue w/red stripe output for setting 2
5: Blue w/yellow stripe output for setting 3
6: Ground to chassis

Then it appears for the head light motors themselves...

1: Connect with #2 above
2: Connect with #3 above
3: Connect with #4 above
4: Connect with #5 above
5: Orange w/green stripe that connects directly to battery with a 7.5A fuse in-line
6: Ground to chassis

These connections at the motors apply to both sides so you would wire them up together.