RB26 180
09-03-2010, 08:42 AM
Car is 99% complete, has ran and driven, however needs new valves. Valves installed by machinist were too short, causing excessive valve lash. I have been building this car for 10 years and my life is completely different than when I started. I have nothing to do with the car scene anymore and have no time for it. Have lost interest in the car.
old pics of car here, I have different wheels on it now, still clean as hell, and almost no miles.
http://s25.photobucket.com/albums/c57/RB26180/rb26180/
1993 s13 hatch about 88,000 miles SHELL FOR SALE AS WELL!!
Individual parts for sale
R33 RB26 SHORT BLOCK $3500
Carillo h beam rods, wiseco pistons, calico coated bearings, ARP head studs, ARP main studs
Custom aluminum sheet metal oil pan for rb26 in s13 chassis $400
RB26 cylinder head bare with cam caps. Clearanced for High lift cams, coolant mod performed $500
Rb26 Cam angle Sensor $200 with AEM wheel, you want have to convert it (it is a royal pain to do)
Rb26 ignition coils with mount bracket $250
Z32 ignitor chip, bought new used for a few months $100
Rb26 individual throttle body kit w/o surge tank, including idle air control valve, $300
With surge tank $400
Grex 272/280 ll.3mm lift cams pair $500
Tomei rb26 lifters, 2mm oversize for high lift cams, installed, never ran $450
N1 oil pump $150
N1 water pump $150
New in plastic Cometic MLS head gasket 88mm bore, $150
Supra 2jzgte stock lifters $180
Exedy twin plate clutch for rb26 $1200
R33 rb26 trans converted to 2wd, coated round tube trans mount for s13, driveshaft for s13 $800
Power steering lines professionally made for rb26 power steering pump, to use stock s13 91-93 ps fluid reservoir, rack, with adapter fittings, power steering cooler. All new $250
Rb26 power steering pump, pulley, bracket non hicas $200
Powdercoated Rear Diff housing, cover, axle stubs, pinion, KAAZ 2 way lsd assembled ready go in, with kaaz oil $1000
with 2 bolt triangle flange, will work with most stock s13 axles
Chromoly axles complete with new boots $500
JIC front tension rods $250
JIC Rear upper control arms $250
Chromoly trac and toe rods, double adjustable with chromoly fine thread rod ends $250 per pair
Powder coated black front lower control arms $100
Powder coated black rear lower control arms $150
Coated black front s14 spindles and new oem 5 lug hubs $300
Coated black rear subframe $100
Coated rear s13 stock spindles, new oem wheel bearings, 5 lug hubs 300zx complete rear brakes, rotors, calipers, e brake assembly $500
Stop tech 4pot big brake upgrade $1500
6 - 1000cc bosch injectors low impedance $400
Custom RB26 polished alum -8 fuel rail for bosch style top feed injectors, most rails are only -6. $100
T76 .81 ar turbo, with .68 ar extra turbine housing $1000
Not a cheap ebay turbo, custom built by a turbo company in CT. 76 compressor inside a bored out 72mm housing. Built to hit full boost between 3500 and 4000 on the rb26. Claim 1000-1200hp potential.
XS engineering intercooler 24x12x3 core with Apexi gtr style end tanks $300
Aeromotive a1000 pump with pre and post filters, one extra new filter in the box $350
Aeromotive 13110 fpr good for up to 2000hp applications $200
Do luck front bumper $150
Carbon fiber extractor style hood $300
Clear front turn signals $60
PJ bonafacio over fenders $250
Wingless rear hatch $200
Signal Auto Carbon fiber mirrors $300
Yashio factory carbon fiber b pillars $150
Work emotion CR KAI bronze 18x9.5 22mm offset front tires are fusion zr1 90% left, rear tires are bfg KDW 295/35/18 90% left. $1800
freshly rebuilt rb26 starter, still new paint, etc $250
I also have several parts that never made it on the car like a huge road race Fluidyne oil cooler, a very nice transmission cooler with fan assembly (I was going to run a small pump assembly to cycle the trans fluid through the cooler, keeping trans temps down on track days.
I am sure there are several things I forgot, this was just off the top of my head.
email is best [email protected]
old pics of car here, I have different wheels on it now, still clean as hell, and almost no miles.
http://s25.photobucket.com/albums/c57/RB26180/rb26180/
1993 s13 hatch about 88,000 miles SHELL FOR SALE AS WELL!!
Individual parts for sale
R33 RB26 SHORT BLOCK $3500
Carillo h beam rods, wiseco pistons, calico coated bearings, ARP head studs, ARP main studs
Custom aluminum sheet metal oil pan for rb26 in s13 chassis $400
RB26 cylinder head bare with cam caps. Clearanced for High lift cams, coolant mod performed $500
Rb26 Cam angle Sensor $200 with AEM wheel, you want have to convert it (it is a royal pain to do)
Rb26 ignition coils with mount bracket $250
Z32 ignitor chip, bought new used for a few months $100
Rb26 individual throttle body kit w/o surge tank, including idle air control valve, $300
With surge tank $400
Grex 272/280 ll.3mm lift cams pair $500
Tomei rb26 lifters, 2mm oversize for high lift cams, installed, never ran $450
N1 oil pump $150
N1 water pump $150
New in plastic Cometic MLS head gasket 88mm bore, $150
Supra 2jzgte stock lifters $180
Exedy twin plate clutch for rb26 $1200
R33 rb26 trans converted to 2wd, coated round tube trans mount for s13, driveshaft for s13 $800
Power steering lines professionally made for rb26 power steering pump, to use stock s13 91-93 ps fluid reservoir, rack, with adapter fittings, power steering cooler. All new $250
Rb26 power steering pump, pulley, bracket non hicas $200
Powdercoated Rear Diff housing, cover, axle stubs, pinion, KAAZ 2 way lsd assembled ready go in, with kaaz oil $1000
with 2 bolt triangle flange, will work with most stock s13 axles
Chromoly axles complete with new boots $500
JIC front tension rods $250
JIC Rear upper control arms $250
Chromoly trac and toe rods, double adjustable with chromoly fine thread rod ends $250 per pair
Powder coated black front lower control arms $100
Powder coated black rear lower control arms $150
Coated black front s14 spindles and new oem 5 lug hubs $300
Coated black rear subframe $100
Coated rear s13 stock spindles, new oem wheel bearings, 5 lug hubs 300zx complete rear brakes, rotors, calipers, e brake assembly $500
Stop tech 4pot big brake upgrade $1500
6 - 1000cc bosch injectors low impedance $400
Custom RB26 polished alum -8 fuel rail for bosch style top feed injectors, most rails are only -6. $100
T76 .81 ar turbo, with .68 ar extra turbine housing $1000
Not a cheap ebay turbo, custom built by a turbo company in CT. 76 compressor inside a bored out 72mm housing. Built to hit full boost between 3500 and 4000 on the rb26. Claim 1000-1200hp potential.
XS engineering intercooler 24x12x3 core with Apexi gtr style end tanks $300
Aeromotive a1000 pump with pre and post filters, one extra new filter in the box $350
Aeromotive 13110 fpr good for up to 2000hp applications $200
Do luck front bumper $150
Carbon fiber extractor style hood $300
Clear front turn signals $60
PJ bonafacio over fenders $250
Wingless rear hatch $200
Signal Auto Carbon fiber mirrors $300
Yashio factory carbon fiber b pillars $150
Work emotion CR KAI bronze 18x9.5 22mm offset front tires are fusion zr1 90% left, rear tires are bfg KDW 295/35/18 90% left. $1800
freshly rebuilt rb26 starter, still new paint, etc $250
I also have several parts that never made it on the car like a huge road race Fluidyne oil cooler, a very nice transmission cooler with fan assembly (I was going to run a small pump assembly to cycle the trans fluid through the cooler, keeping trans temps down on track days.
I am sure there are several things I forgot, this was just off the top of my head.
email is best [email protected]