Complete CA18DET w/ extras & 92 coupe! $1200

[buddha]

CA18DET & Shell $1200

Location: Central New Jersey

Engine
- Complete CA18DET with wiring harness converted for US S13. (With knock sensor wire done right)
- Extra Assembled CA18DET block
- 5-speed transmission
- Mechanical fan and shroud
- New OE Nissan timing belt, tensioners and water pump installed on the assembled engine(Have maybe 5000 miles on them)
- Brand new OE Nissan complete gasket set.(Every gasket including head)
- New cold start idle valve in box from japan(Almost every CA needs this!)
- New coolant temp sensor installed.
- New O2 Sensor in turbo elbow
- Mines tuned ECU.Tuned for stock fuel injectors and stock maf FMIC, Exhaust, and .9 bar boost on a t-25/28.

Turbo
- S14 T-28 Turbo
- ARC front mount intercooler that uses stock side mount intercooler piping.(You can run a full size battery)
- Blitz Dual Drive Blow off valve
- Stock elbow, downpiped and 80mm test pipe included

Other & Extras
- Nismo engine and tranmission mounts(The right ones made for the ca18)
- Extra set of 4 Ignition Coils
- Extra Ignitor chip
- Garrett Turbo rebuild kit.(Packaging is ravaged, but it's never been opened)
- Stock CA18DE(non turbo) ecu. I've been told that this can be socketed and tuned for a turbo setup. I never verfied that, but I'll include it since I'd have no use for it.
- New silicone radiator hoses
- Anything else I happen to find

Description
Here we have a Complete CA18DET swap. It comes with many many cool things. Why is the price so low? Here's the catch. As noted in the pictures. There is a flywheel bolt broken off in the crankshaft on the assembled engine. Hence why there is an additional CA18 block. My original plan was to replace the crankshaft in the assembled engine with the good one in the extra block. I simply don't have time to play around with this engine anymore. So I took the CA out and run a stock KA24 engine now. Also, when we took the engine out, there was a little oil in the turbo inlet, I never noticed anything out of the ordanary when running the car. The oil is most likely from the crankcase ventilation tube that goes into the intake, but I have a Garrett turbo rebuilt included just incase.

Please do not hesitate to ask anything about this engine. I've been up front with everything and will not hide anything. Either post in the thread, or email me at [email protected]


What's needed to run
- Crankshaft swapped, or broken bolt drilled out. Currently the bolt holes in the crank are 7/16" -20 thread. The stock flywheel bolt holes were bored to 7/16"
- New flywheel.I have the flywheel, but the bolt holes are bored to 7/16" and it is pretty worn. If you manage to get the bolt out and the threads are still good in the crank, you will need to bore out the bolt holes in your replacement crankshaft to 7/16"
- Clutch
- Cold start valve installed (very easy. The hard part was getting it, and that's already done!)


Engine
http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1193.jpg


Broken Bolt
http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1194.jpg


5-Speed Transmission
http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_0001.jpg


Extra block, T-28, elbow, downpipe, testpipe, cold start valve and one of the Nismo mounts
http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1199.jpg
http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_0008.jpg


Blitz Dual Drive
http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1202.jpg


ARC Intercooler
http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_0002.jpg
http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_0003.jpg
http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_0007.jpg

1992 Nissan 240sx Coupe shell

Description

This is a rolling shell that needs a few things. Title is clean. Rust free.(a couple surface spots here or there, nothing major at all)

What it has
- Rust free and clean.
- Sunroof and HUD windshield(non hud dash install however)
- Roll chassis
- 7 spoke se wheels
- Clear title in hand
- Brand new front engine bay harness

What's needed
- Misc things
- brake booster & master
- Brake line for FL
- Seats
- Front end panels & hood
- possibly some other small things I can' remember.

Coupe pics


http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1191.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1192.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1195.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1196.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1198.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1200.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1183.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1184.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1185.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1186.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1187.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1188.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1177.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1180.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1181.jpg

http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1182.jpg

They need a loving home!
http://img.photobucket.com/albums/v156/buddha460/240sx%20stuff%20for%20sale/DSC_1190.jpg

[noahd86]

Hey you wouldn't consider selling me just the ca18 harness by it self would you?

[Backwoodsboy]

have you tried an easy out, vise grips or welding a nut onto that broken bolt...just helping ya out man...

[zero.offset]

Thats one hell of a deal, GLWS

[Noxy]

Just a heads up, if i'm not mistaken he already sold this. Thats what it said on nico at least...

[Slammed Assassin]

awesome deal!!

[matbmorr]

Damn i wish i could get that ca :(

[racerx2k1]

Last Activity: 05-13-2010 05:30 PM