enjoisk8board891
04-15-2010, 10:44 AM
Well Ive had this on KA-T for about a week for obvious reasons. So now im tryin zilvia.
Alright guys I finally had time to pull the motor and get some decent pics. Ya there with an iphone but its the best i can do. I could get more pics if needed. But heres the shakedown on everything. Yes i did lower the prices on everything because I NEED MONEY
Built KA and trans-1700 obo
Arias stock bore pistons
Turbo240 rods
Coated calico bearings
Oil pump pressure valve shimmed
ARP main studs
Align honed
Block deck surface o-ringed
Time-serts installed in block for head studs (super strong)
11mm head studs included
Bottom End has about 1500 miles
I Bought the bottom end from Chris over at AMS about a year ago. I pulled the head off my old motor, had NAPA re-machine everything to factory specs. Put it together and its pretty much been sitting in the car since then as i slowly added things to it. Well I just bought a dodge ram for my new dd. So this project kind of came to a halt and i need money. Anyways the only thing that might need done to the motor is adjusting of the timing and it was recommended (not necessary) to replace the rod bearings. I do have a set of clevets ill throw in for free.
Transmission
I bought the trans off of a user on Zilvia. Its off of a 95 and i was told it was in good working order. The only thing is i had to fix one of the plugs and it will not come with a speed sensor. I also purchased a clutch kit off zilvia tht was brand new rated at, from what i can remember 340 ft/lbs of torque. But we'll say 300 because im not too sure.
T3 60/1-600 shipped
Brand new. Only mounted. NO EXHAUST EVER RAN THREW IT. Theres no shaft play
well on to the pics. Please EMAIL at [email protected] me with any questions due to me not checking the forums as much. Thanks!
http://i515.photobucket.com/albums/t358/Enjoisk8board891/b08fcc64.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/ddcc950a.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/88602622.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/ce4bc62c.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/45960b5b.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/b11b46de.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/05c80d95.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/857d6171.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/24a39f75.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/39799c5d.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/50271ba6.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/697bf3ef.jpg
Please email me at [email protected] if your interested
Thanks
D
Alright guys I finally had time to pull the motor and get some decent pics. Ya there with an iphone but its the best i can do. I could get more pics if needed. But heres the shakedown on everything. Yes i did lower the prices on everything because I NEED MONEY
Built KA and trans-1700 obo
Arias stock bore pistons
Turbo240 rods
Coated calico bearings
Oil pump pressure valve shimmed
ARP main studs
Align honed
Block deck surface o-ringed
Time-serts installed in block for head studs (super strong)
11mm head studs included
Bottom End has about 1500 miles
I Bought the bottom end from Chris over at AMS about a year ago. I pulled the head off my old motor, had NAPA re-machine everything to factory specs. Put it together and its pretty much been sitting in the car since then as i slowly added things to it. Well I just bought a dodge ram for my new dd. So this project kind of came to a halt and i need money. Anyways the only thing that might need done to the motor is adjusting of the timing and it was recommended (not necessary) to replace the rod bearings. I do have a set of clevets ill throw in for free.
Transmission
I bought the trans off of a user on Zilvia. Its off of a 95 and i was told it was in good working order. The only thing is i had to fix one of the plugs and it will not come with a speed sensor. I also purchased a clutch kit off zilvia tht was brand new rated at, from what i can remember 340 ft/lbs of torque. But we'll say 300 because im not too sure.
T3 60/1-600 shipped
Brand new. Only mounted. NO EXHAUST EVER RAN THREW IT. Theres no shaft play
well on to the pics. Please EMAIL at [email protected] me with any questions due to me not checking the forums as much. Thanks!
http://i515.photobucket.com/albums/t358/Enjoisk8board891/b08fcc64.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/ddcc950a.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/88602622.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/ce4bc62c.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/45960b5b.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/b11b46de.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/05c80d95.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/857d6171.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/24a39f75.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/39799c5d.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/50271ba6.jpg
http://i515.photobucket.com/albums/t358/Enjoisk8board891/697bf3ef.jpg
Please email me at [email protected] if your interested
Thanks
D