thedr1ftkid
04-13-2010, 04:00 PM
I have most of the parts to turbo a KA for sale, pictures and descriptions below.
Contact: 503-729-3117 or e-mail [email protected]
Location: Portland, OR
Shipping: Available
First off I have a Holset H1C turbocharger, I bought it awhile ago and never ended up using it. It has some sort of coating on the intake side, and there is very minimal shaft play. The wheels are also in good shape.
Here's a little info on it from 10SecRex from d-series.org:
H1C/WH1C:
In 1994, there was the Wh1c which has pretty much the identical compressor as the hx35 but with a Vband compressor cover. The turbine wheel is the same. It will bolt into the BEP bolton hx35 turbine housing. It has 4 bolts at the housing instead of 6. So you will need to buy 2 more bolts and use 6 washers cut to make a flat side. Honestly, I just used bolts that were cut a little short and the bolt head was wide enough to pull the chra to the turbine housing. No sealing issues. Since the Wh1c is for all practical purposes an 8blade hx35 the spool and flow is the same too.
I have the big h1c. It comes on the INTERCOOLED 1991-1993 cummins pickups. It has the webbing for MWE but no groove cut like the hx35/wh1c has. This turbo I term the big h1c because it has a 54mm compressor inducer and same exducer than the 8blade hx35/Wh1c. The other h1c is the small h1c found on the NON-intercooled cummins pickups. This has a 50mm inducer but only 7blades and has no webbing for MWE. Less blades helps flow, but so does a larger inducer diameter. The most whp ever recorded on a gas 4cylinder with the small h1c was done on a KA24 nissan: 411whp. Since the big h1c has a 4mm larger inducer and the same turbine wheel as the hx35, it is safe to say that it flows enough for between 411whp and 500whp. The diesel sources state that it flows SLIGHTLY less than the early hx35. So 4lb/min less than the 8blade hx35 puts the flow of the big h1c at 48-49lb/min right where a 50-trim or 20g is. The small bep housing is all that's needed to get the most from the compressor and the spool speed is 20+psi by 3500rpms.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/TurboIntake.jpg
http://i247.photobucket.com/albums/gg155/thedr1ftkid/TurboSide.jpg
http://i247.photobucket.com/albums/gg155/thedr1ftkid/TurboExhaust.jpg
$250 +shipping
KA24DE SS turbo manifold ramhorn style. I think it's just an eBay one but it's brand new and looks to be pretty good quality.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/ManifoldBottom.jpg
http://i247.photobucket.com/albums/gg155/thedr1ftkid/ManifoldTop.jpg
$60 +shipping
N60 MAFS off a Maxima. Cost effective alternative to z32 MAFS for people looking to stay around 350hp. Comes with good pigtail. Screens are intact and it's clean.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/MAFSIDSticker.jpg
http://i247.photobucket.com/albums/gg155/thedr1ftkid/MAFSInside.jpg
http://i247.photobucket.com/albums/gg155/thedr1ftkid/MAFSFull.jpg
$50 +shipping
eBay RFL BOV knockoff. Used for a day and replaced with the next one I'm selling.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/SilverBOV.jpg
$40 +shipping
eBay Greddy knockoff BOV w/ manual boost controller, used for a week and replaced with an EBC and SSQV.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/RedBOV.jpg
$50 +shipping
21x7x2.5 intercooler with piping, couplers and clamps. Was used on a KA-T setup on a single cam, not sure if it lines up on a dual cam.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/Intercooler-1.jpg
$150 +shipping
Make offers, or take all for $450 +shipping!
Contact: 503-729-3117 or e-mail [email protected]
Location: Portland, OR
Shipping: Available
First off I have a Holset H1C turbocharger, I bought it awhile ago and never ended up using it. It has some sort of coating on the intake side, and there is very minimal shaft play. The wheels are also in good shape.
Here's a little info on it from 10SecRex from d-series.org:
H1C/WH1C:
In 1994, there was the Wh1c which has pretty much the identical compressor as the hx35 but with a Vband compressor cover. The turbine wheel is the same. It will bolt into the BEP bolton hx35 turbine housing. It has 4 bolts at the housing instead of 6. So you will need to buy 2 more bolts and use 6 washers cut to make a flat side. Honestly, I just used bolts that were cut a little short and the bolt head was wide enough to pull the chra to the turbine housing. No sealing issues. Since the Wh1c is for all practical purposes an 8blade hx35 the spool and flow is the same too.
I have the big h1c. It comes on the INTERCOOLED 1991-1993 cummins pickups. It has the webbing for MWE but no groove cut like the hx35/wh1c has. This turbo I term the big h1c because it has a 54mm compressor inducer and same exducer than the 8blade hx35/Wh1c. The other h1c is the small h1c found on the NON-intercooled cummins pickups. This has a 50mm inducer but only 7blades and has no webbing for MWE. Less blades helps flow, but so does a larger inducer diameter. The most whp ever recorded on a gas 4cylinder with the small h1c was done on a KA24 nissan: 411whp. Since the big h1c has a 4mm larger inducer and the same turbine wheel as the hx35, it is safe to say that it flows enough for between 411whp and 500whp. The diesel sources state that it flows SLIGHTLY less than the early hx35. So 4lb/min less than the 8blade hx35 puts the flow of the big h1c at 48-49lb/min right where a 50-trim or 20g is. The small bep housing is all that's needed to get the most from the compressor and the spool speed is 20+psi by 3500rpms.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/TurboIntake.jpg
http://i247.photobucket.com/albums/gg155/thedr1ftkid/TurboSide.jpg
http://i247.photobucket.com/albums/gg155/thedr1ftkid/TurboExhaust.jpg
$250 +shipping
KA24DE SS turbo manifold ramhorn style. I think it's just an eBay one but it's brand new and looks to be pretty good quality.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/ManifoldBottom.jpg
http://i247.photobucket.com/albums/gg155/thedr1ftkid/ManifoldTop.jpg
$60 +shipping
N60 MAFS off a Maxima. Cost effective alternative to z32 MAFS for people looking to stay around 350hp. Comes with good pigtail. Screens are intact and it's clean.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/MAFSIDSticker.jpg
http://i247.photobucket.com/albums/gg155/thedr1ftkid/MAFSInside.jpg
http://i247.photobucket.com/albums/gg155/thedr1ftkid/MAFSFull.jpg
$50 +shipping
eBay RFL BOV knockoff. Used for a day and replaced with the next one I'm selling.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/SilverBOV.jpg
$40 +shipping
eBay Greddy knockoff BOV w/ manual boost controller, used for a week and replaced with an EBC and SSQV.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/RedBOV.jpg
$50 +shipping
21x7x2.5 intercooler with piping, couplers and clamps. Was used on a KA-T setup on a single cam, not sure if it lines up on a dual cam.
http://i247.photobucket.com/albums/gg155/thedr1ftkid/Intercooler-1.jpg
$150 +shipping
Make offers, or take all for $450 +shipping!