240racer2
02-11-2010, 07:42 PM
hey guys this is a legit garrett gt28rs in near new condition
GT2860RS-The Disco Potato
Horsepower 250 - 360
Displacement 1.8L - 3.0L
-76mm/3 in. Compressor Inlet trim
- T3 5-bolt discharge flange
-63 AR Exhaust
- Ball bearing
- Oil & Water-cooled bearing system
- Upgrade turbocharger for GT2554R (471171-3) and GT2560R (466541-1); turbine housing flanges are outline interchangable
- T25 turbine inlet flange
- Ideal for smaller displacement engines making up to 360 hp
- aftermarket hks wastegate, stock set at 10lbs
- less than 5,000 miles on this, with little or no shaft play
- lookin to get a 2871r so i need this gone
-if you have the cash and are serious i might sell the ecu with it thats a jwt tuned for 740cc, z32, and disco potato http://www.houston240sx.com/images/smilies/smile.gif
-makes amazing power..on my setup its prolly at about 320whp with bc 264s, FMIC, 255lph, fully forged bottom end, and built head.... and the turbo lag it barely noticible, prolly starts spooling at around 2,700 and hits full boost by 3,000 to 3,200...basically its a beast for very quick acceleration
*edit* pics (as good as i could make em lol)
http://i733.photobucket.com/albums/w...s/P2090536.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090536.jpg)
http://i733.photobucket.com/albums/w...s/P2090537.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090537.jpg)
http://i733.photobucket.com/albums/w...s/P2090538.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090538.jpg)
http://i733.photobucket.com/albums/w...s/P2090539.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090539.jpg)
http://i733.photobucket.com/albums/w...s/P2090540.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090540.jpg)
http://i733.photobucket.com/albums/w...s/P2090541.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090541.jpg) (actuator broke so i got someone to weld it on lol, its not coming off either...http://www.houston240sx.com/images/smilies/smile.gif)
PRICE DROP BUMP!!
-askin price is 800..... $900 with the braided steel lines or $1,100 with lines and manifold...plus shipping... please dont low ball if you dont have the cash dont even comment thanks!
GT2860RS-The Disco Potato
Horsepower 250 - 360
Displacement 1.8L - 3.0L
-76mm/3 in. Compressor Inlet trim
- T3 5-bolt discharge flange
-63 AR Exhaust
- Ball bearing
- Oil & Water-cooled bearing system
- Upgrade turbocharger for GT2554R (471171-3) and GT2560R (466541-1); turbine housing flanges are outline interchangable
- T25 turbine inlet flange
- Ideal for smaller displacement engines making up to 360 hp
- aftermarket hks wastegate, stock set at 10lbs
- less than 5,000 miles on this, with little or no shaft play
- lookin to get a 2871r so i need this gone
-if you have the cash and are serious i might sell the ecu with it thats a jwt tuned for 740cc, z32, and disco potato http://www.houston240sx.com/images/smilies/smile.gif
-makes amazing power..on my setup its prolly at about 320whp with bc 264s, FMIC, 255lph, fully forged bottom end, and built head.... and the turbo lag it barely noticible, prolly starts spooling at around 2,700 and hits full boost by 3,000 to 3,200...basically its a beast for very quick acceleration
*edit* pics (as good as i could make em lol)
http://i733.photobucket.com/albums/w...s/P2090536.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090536.jpg)
http://i733.photobucket.com/albums/w...s/P2090537.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090537.jpg)
http://i733.photobucket.com/albums/w...s/P2090538.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090538.jpg)
http://i733.photobucket.com/albums/w...s/P2090539.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090539.jpg)
http://i733.photobucket.com/albums/w...s/P2090540.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090540.jpg)
http://i733.photobucket.com/albums/w...s/P2090541.jpg (http://i733.photobucket.com/albums/ww338/240racer2/turbos/P2090541.jpg) (actuator broke so i got someone to weld it on lol, its not coming off either...http://www.houston240sx.com/images/smilies/smile.gif)
PRICE DROP BUMP!!
-askin price is 800..... $900 with the braided steel lines or $1,100 with lines and manifold...plus shipping... please dont low ball if you dont have the cash dont even comment thanks!