Brand new set of Drift Freaq custom urethane KA/SR engine mounts.

[drift freaq]

This is a brand new set high durometer Polyurethane engine mounts $120 is the price.
I used to sell these all the time in a group buy here many people have run or run them.

They do not have solid rods all the way through so they do not transfer vibration. They are made from high durometer Urethane.
Not Polyurethane tubes or Industrial urethane window caulk you buy at Home Depot.
The mounts are track tested and have been used on many race cars. (THIS SET IS NEW) I am talking about these mounts in General.

They are stiffer than Nismo mounts, but not bone jarring, in fact they are quite nice.

Oh and if you are going to use these on a turbo car? I suggest strongly you keep your exhaust side stock heatshield and use it with these.

http://i705.photobucket.com/albums/ww52/driftfreaq/IMG_0573.jpg

[Charlie]

Do these raise the engine a bit or lower it? I think something was mentioned on your last thread but I'm not all that sure?

[drift freaq]

Do these raise the engine a bit or lower them? I think something was mentioned on your last thread but I'm not all that sure?

they lower it.

[Charlie]

they lower it.

I just went found your old thread and found the post. Hmm do you plan on making another version of these mounts where they raise the engine like the nismo ones?

[drift freaq]

I just went found your old thread and found the post. Hmm do you plan on making another version of these mounts where they raise the engine like the nismo ones?

ah most people like the fact that it lowers it. In fact people complain about the Nismo mounts raising the engine up to much.

[Charlie]

Maybe it because I have fucked up mounts and its making the oil pan sit like 3/4 lower then the sway bar that's why I want mounts to raise the engine higher LOL. Do you know if the oil pan(KA) will still be lower than the sway bar with your mounts installed?

[drift freaq]

Maybe it because I have fucked up mounts and its making the oil pan sit like 3/4 lower then the sway bar that's why I want mounts to raise the engine higher LOL. Do you know if the oil pan(KA) will still be lower than the sway bar with your mounts installed?

it will not be lower than the swaybar.

[tranjq]

I got these on my 90' s13 ka24e and have had zero problems. Thanks Drift Freaq for chimming in on my post so everyone would know who is the maker of these mounts.

You should consider making tranny mounts too!

[drift freaq]

I got these on my 90' s13 ka24e and have had zero problems. Thanks Drift Freaq for chimming in on my post so everyone would know who are the makers of these mounts.

You should consider making tranny mounts too!

they cost to much to manufacture given the overall interest.

[tranjq]

they cost to much to manufacture given the overall interest.

Well how much would you charge for one? Would it work for ka and sr trannies?

[drift freaq]

Well how much would you charge for one? Would it work for ka and sr trannies?

Well see its about cost of setup and runs. I would have to design it. Then make it and I would have to do an initial run of many to start. There is not enough business to warrant it. I would just lose money.

If hundreds of people were buying these mounts it might be feasible but given the current 240 owners fickleness in buying stuff? Not going to happen. Sorry. I can offer you a Nismo trans mount for like $45 which is pretty damn cheap.

[drift freaq]

back on up for this.

[MELLO*SOS]

Dude! I need these... Going KA-T on my s14..

Hit me again pls.

[drift freaq]

Dude! I need these... Going KA-T on my s14..

Hit me again pls.

you have been p.m.'d

[drift freaq]

last bump for this.

[drftkng951]

any pictures of these installed?
how well do they handle heat?

[drift freaq]

any pictures of these installed?
how well do they handle heat?

ah I would have to dig one up. As far as heat goes like I wrote above I strongly recommend you use a stock heatshield on the exhaust side. If you do that everything is fine, extreme heat can affect any rubber or Urethane.

There are people in this thread that have bought these several years ago for their car and are now buying them for their new car. Yes I have two sets.

[MELLO*SOS]

Thanks Dave, got the mounts in today. I should have remembered to have you send me a nismo trans mount at the same time :)

Also you guys asking questions about these mounts -- they are simply great! I've used these on my s13 for a couple years without any problem. The new set I picked up are for my S14 KA-T setup. Dave (drift freaq) is a solid guy and makes good quality parts, if you need mounts don't hesitate to pick up a pair of these!