5.0 Engine swap lots of parts

[anotheraznguy]

Want tire spinning power with out the wallet spinning price!! :)
Great Budget 300 hp Ford 5.0L engine conversion ready to drop into your Nissan "S" chassis.
Why spend 10k dollars on a ls1 swap when you can get lots of tq lots of hp and a damn awesome sound

Lots of awesome stuff. Selling as a whole...

Asking $2,500.00 picked up

i checked on shipping and it is crazy!!! you are better off picking it up or you can arrange shipping.

Parts are located in Northern California, Fremont

All you needto do is wire it up, order up the driveshaft, make a header-back exhaust, and it is time for

burnouts!!

Conversion parts:

- Custom headers / custom oil pan / custom motor mount / custom tranny mount
- AN fittings and earl's perform-o-flex high pressure hose for power steering conversion directly to 240sx rack
- Includes all sensors for MAP or MAF ECU setup.
- Complete MAP harness/ECU
- Torn down MAF harness ready to solder up and go that route if you want (you wil still need the MAF ECU)

Stock Ford Parts:

- T5 Tranny w/ used clutch/flywheel, shifter/handle
- Stock Mustang T5 Transmission crossmember
- Stock Mustang drifeshaft
- 5.0 Short Block w/ parts unassembled
- 5.0 Heads
- Stock oil dipstick
- Water Pump
- x2 Alternator w/mounting brackets/tensioner
- x2 Air Condition Pump W/mounting brackets
- x2 Flywheel
- x1 Used Power Steering Pump w/mounting brackets
- x1 NEW power steering Pump w/mounting brackets
- Smog pump (only for you CA people haha)
- Starter
- Starter silinoid
- Stock intake Elbow w/ Air box w/filter
- Mustang Clutch/brake Pedal assembly
- Clutch cable / Quadrant
- Stock Headers
- Stock Lower Intake Manifold
- Stock Upper Intake Manifold
- Stock throttle body
- Stock fuel rail w/19lbs injectors
- Stock EGR plate W/EGR valve
- Stock valve covers
- Stock ignition coil

2nd Engine:

- Assembled Long block
- Installed Hot Aftermarket E303 Cam
- Underdrive Crank Pulley
- High-Flow Water pump


Aftermarket goodies:

- New Ford Racing Mini Tq Starter
- New Polished 75mm Thorttle Body
- New BBK Throttle Body Gasket
- New Edelbrock Performer Intake Mani Gasket Set
- New Ford Motorsport Chrome distributor hold down clamp
- New Hamburg Cork Oil Pan Gasket
- MSD 6AL w/ Pillls
- New MSD Vibration Mounts
- New Vehicle Speed Sensor
- New EFI Spacer Kit Performer Rpm 3/8 inch
- New Energy Suspension Tranny Mount Urethane
- New Ford Motorsports AC Eliminator Kit
- Moroso Solid Motor Mounts
- New Chrome Oil Dipstick
- New Smog Pump Elim Bracket (moves PS pump into a better upright position)
- New Chrome Msd Blaster Coil
- New Universal Chrome Coil Bracket
- Howe Eng. 1 5/16 stroke slave cylinder pull type
- Wilwood 1 Inch Master Cylinder
- Earls AN adapters w/high pressure SS line for master to slave connection (pre-built)
- New Ford Motorsport larger racing Oil Pump Shaft
- New ARP Pressure Plate Bolts
- New Milidon Ford Oil Pan Studs
- New Zoom Clutch/Pressure Plate/TOB/Pilot Bearing
- 30 LB Injectors w/ matched 75mm Maf (these injectors can also be used with MAP but tuning will be required)
- Edelbrock RPM Manifold
- New Edelbrock gasket set for manifold
- New Trick flow 3/8" intake manifold spacer
- Larger capasity SN 95 (94-95) fuel rails w/BBK Fuel Pressure regulator & BBK Fuel Pressure Gauge pre-installed

- Polished Tall Ford Racing Valve Covers
- Msd Plug Wires w/ MSD Cap / Rotor / installed on stock distributor
- New oil filter relocation kit

Check it out Here is what you get!!:

http://i413.photobucket.com/albums/pp214/jdmotorworks/Conversion%20Sale/DSC03784.jpg?t=1242530975


Also for those who dont know, we were the ppl that also made another v8 240sx..
Take a look at see who did all the wrenching on this car =)

YouTube - AutoRnD's S13 5.0 Swap (http://www.youtube.com/watch?v=BCKAi0PviM4)

A small taste of things i have


http://i413.photobucket.com/albums/pp214/jdmotorworks/Conversion%20Sale/DSC03766.jpg?t=1242531581
http://i413.photobucket.com/albums/pp214/jdmotorworks/Conversion%20Sale/DSC03758.jpg?t=1242531641
http://i413.photobucket.com/albums/pp214/jdmotorworks/Conversion%20Sale/DSC03712.jpg?t=1242531683
http://i413.photobucket.com/albums/pp214/jdmotorworks/Conversion%20Sale/DSC03715.jpg?t=1242531711
http://i413.photobucket.com/albums/pp214/jdmotorworks/Conversion%20Sale/DSC03676.jpg?t=1242531746
http://i413.photobucket.com/albums/pp214/jdmotorworks/Conversion%20Sale/DSC03672.jpg?t=1242531790


For all the pictures check it out:

Conversion Sale pictures by jdmotorworks - Photobucket (http://s413.photobucket.com/albums/pp214/jdmotorworks/Conversion%20Sale/)

Email me at [email protected]
or call me 510 676 5975 - Josh





________________________________

[matt11145]

Nationwide Engine Freight Service (http://www.engineshipping.com) does great rates. i shipped a motor from pa to fl for only $254

just figured it might help sell your stuff if people know they can ship it for cheap.

[anotheraznguy]

bump! need this gone eventually

[anotheraznguy]

bump with the v8 power

[Killa_D]

damn cant believe you haven't sold this yet bump again.

[Real**Fresh]

wow this is still avail........

[anotheraznguy]

yeah economy just isnt waht it is anymore..
anyways.. i am willing to deliver up to socal and as far north as 6 hours till take me for a fee. let me know guys