dkwasherexd
10-29-2009, 02:31 AM
Up for sale is1986 Mazda rx7 Na, and has tons of mods. Large street port irons, and large street ported turbo 2 housings.The car comes with Jacobs Rotary ignition box wired up to msd coils for more power than the stock factory igniter coils. Its clean inside and out. Full s5 interior, turbo 2 seats,and back seats. I just rebuilt the engine last week and drove it this week. Ive only driven it 60 miles and about 2 hours of idle time. The engine is still breaking in! The car runs very strong, and is very fast. The engine is built, and ready to race/grip/drift at the track. I must say Im pretty happy with the engine build[This is my 6th engine build and by far my favorite] After breaking in, Im predicting it to put out around 170-180whp. Port and polish the manifolds and throttlebody and you can aim for 200whp. You can take it all the way past 8 grand rpm. For now take it easy and break in the motor for about 1500 miles. After the odometer reaches 100 miles, do a full oil change, coolant flush and new oil filter. Then at 500 miles do another oilchange, then at 1000 miles do another oil change. Drive it under 4000 rpm and take it easy.
If broken in properly, the motor should last well over 100,000 miles. The lsd locks strong, car corners very well with the suspension.
This is a perfect daily driver and track car.
Engine build parts list
Large Street ported Irons
Large street ported Housings
Brand new Oem stationary bearings
Brand new oem rotor bearings
Brand new apex seal springs
brand new side seal springs
brand new 93+ fd corner springs
Oem Mazda FD 2 Piece apex seals
New Rotary aviation water jacket seals
New Rotary aviation viton oil control seals
New Rotary aviation front and rear main seals
banzai block off plates/blocked off emissions
Oil metering pump is removed, block off plate[Runs on 2stroke oil premix]
Premix it one ounce of 2 stroke oil per gallon
s5 and s4 turbo 2 housings
s4 na rotors
s4 turbo 2 water pump and housing
turbo 2 secondary injectors
brand new primary injector clips
rebuilt primary injectors with Brand new orings, and filter
brand new NGK spark plugs
Brand new altenator belt
Racing Beat Race headers
racing beat dual exhaust[$1000+ value]
Reman Altenator
Jacobs Rotary Ignition pack
Msd trailing ignition coils
booster ignition packs on leading coil
depowered steering rack[just add a PS pump and bracket if you want powersteering]
Black magic efan [automaticly turns on at 180 degrees]fully adjustable
Short shifter
low mileage tranny
s4 clutch type LSD
SS clutch line
very strong locking ebrake
5 lug
Kyb agx 5 way adjustable shocks
popup headlights
eibach lowering springs
momo steering wheel
quick release
power windows
power sunroof
gp sports body kit
s5 moldings
s4 tail lights
The bad
During the rebuild, I didnt have a oil pan gasket. So it leaks just a little bit, but I used alot of RTV. The body has alot of small dings.
Get a new oil pan gasket, do some body work, paint the car and you got yourself a show car and full track car.
I have the title and all paperwork.
$5000 obo
Damn I really didnt want to sell this car. After driving it today it made me really want to keep her. :( Unfortunately my girl friend has a bunch of hospital bills that needs to be paid off.. Im out of debt myself :) Now I just have to help out my gf..
I guess I can always build another dd rx7 later on..
Anyways onto the buisness talk.
Trade are welcomed.. The car is being sold as is. No returns. As soon as you sign the bill of sale, its yours.
The reason why Im strict about that, is because I had issues in the past of buyers changing their mind and coming back later on that day to return what they bought.
So I learned to sell "as is and no returns."
When you buy it Il explain how to premix the 2 stroke oil, and how to adjust idle if you ever need to, and what to dos on a rotary.
Video of the first startup last week after the rebuild.
YouTube - dkwasherexd and ilikeeatpoo rebuilds a Streetported 13b engine 1st startup (http://www.youtube.com/watch?v=_2PWUWUpY9E)
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3002.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3001.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3005.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCI11521.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3007.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3008.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3013.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3010.jpg
If broken in properly, the motor should last well over 100,000 miles. The lsd locks strong, car corners very well with the suspension.
This is a perfect daily driver and track car.
Engine build parts list
Large Street ported Irons
Large street ported Housings
Brand new Oem stationary bearings
Brand new oem rotor bearings
Brand new apex seal springs
brand new side seal springs
brand new 93+ fd corner springs
Oem Mazda FD 2 Piece apex seals
New Rotary aviation water jacket seals
New Rotary aviation viton oil control seals
New Rotary aviation front and rear main seals
banzai block off plates/blocked off emissions
Oil metering pump is removed, block off plate[Runs on 2stroke oil premix]
Premix it one ounce of 2 stroke oil per gallon
s5 and s4 turbo 2 housings
s4 na rotors
s4 turbo 2 water pump and housing
turbo 2 secondary injectors
brand new primary injector clips
rebuilt primary injectors with Brand new orings, and filter
brand new NGK spark plugs
Brand new altenator belt
Racing Beat Race headers
racing beat dual exhaust[$1000+ value]
Reman Altenator
Jacobs Rotary Ignition pack
Msd trailing ignition coils
booster ignition packs on leading coil
depowered steering rack[just add a PS pump and bracket if you want powersteering]
Black magic efan [automaticly turns on at 180 degrees]fully adjustable
Short shifter
low mileage tranny
s4 clutch type LSD
SS clutch line
very strong locking ebrake
5 lug
Kyb agx 5 way adjustable shocks
popup headlights
eibach lowering springs
momo steering wheel
quick release
power windows
power sunroof
gp sports body kit
s5 moldings
s4 tail lights
The bad
During the rebuild, I didnt have a oil pan gasket. So it leaks just a little bit, but I used alot of RTV. The body has alot of small dings.
Get a new oil pan gasket, do some body work, paint the car and you got yourself a show car and full track car.
I have the title and all paperwork.
$5000 obo
Damn I really didnt want to sell this car. After driving it today it made me really want to keep her. :( Unfortunately my girl friend has a bunch of hospital bills that needs to be paid off.. Im out of debt myself :) Now I just have to help out my gf..
I guess I can always build another dd rx7 later on..
Anyways onto the buisness talk.
Trade are welcomed.. The car is being sold as is. No returns. As soon as you sign the bill of sale, its yours.
The reason why Im strict about that, is because I had issues in the past of buyers changing their mind and coming back later on that day to return what they bought.
So I learned to sell "as is and no returns."
When you buy it Il explain how to premix the 2 stroke oil, and how to adjust idle if you ever need to, and what to dos on a rotary.
Video of the first startup last week after the rebuild.
YouTube - dkwasherexd and ilikeeatpoo rebuilds a Streetported 13b engine 1st startup (http://www.youtube.com/watch?v=_2PWUWUpY9E)
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3002.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3001.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3005.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCI11521.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3007.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3008.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3013.jpg
http://img.photobucket.com/albums/v615/iamachickenduck/DSCF3010.jpg