FS: S14 Koni/GC setup

[yudalicious]

My loss is your gain. Everything (except when noted) is brand new, never even mounted on a car.

Front:
-S14 Koni yellows already inserted into stock tubes meticulously cleaned up and repainted with flat black.
-7" 400# 2.5ID Hyperco springs
-Ebay special camber plates
-TechnoToyTuning upper hats
-Ground Control bump stops, already trimmed
-Roller bearings on the bottom of the springs
-Most of the miscellaneous hardware, just need another small sleeve

Rear:
-S14 Koni yellows rebuilt and revalved to handle 300# at the minimum setting (tried to convert to externally adjustable, but Koni does not have a hollow rod long enough at the time)
-7" 300# 2.5ID Eibach racing springs (used)
-Ground control bump stops
-TechnoToyTuning top hats
-You can either use a stock top mounting solution or use aftermarket such as the Tein top mounts

Misc:
-a **** ton of random sleeves, washers
-a few more TechnoToyTuning upper hats
-a pair or two of used 5" Eibach racing springs, I don't remember off the top of my head the specifics, probably not very helpful for 240 setups.

Located in Atlanta/Gwinnett. At this time I am entertaining local offers (packing and shipping will be a pain and expensive) and am not parting out. Asking for $900 firm. I spent at least $1200-1300 collecting everything, the small stuff really adds up. If you are not local and are interested, email me maybe we can work something out.

PLEASE EMAIL [email protected] that is the easiest way to reach me I don't check forums often.

http://photos-g.ak.fbcdn.net/photos-ak-snc1/v2064/85/63/2600283/n2600283_34376294_9740.jpg
http://photos-f.ak.fbcdn.net/photos-ak-snc1/v344/85/63/2600283/n2600283_33894445_6888.jpg

[305_hustler]

so is anything else needed for this setup? and does it come with the koni yellow lifetime warranty

[NINJASPY]

wish I could afford, nice stuff.

[eye-5]

Where were you a year ago? Nice setup and good find for anyone looking for a quality performance suspension. Kicks the crap out of most of the Japanese coilovers out there.

[yudalicious]

so is anything else needed for this setup? and does it come with the koni yellow lifetime warranty

Hey sorry for the slow reply I don't check forums often so I rely on email. I believe these DO come with the koni warranty but I am not 100% sure on warranty status after having the product change hands. Although I don't think it's anything to worry about, fronts are brand new, rears are rebuilt/revalved by Koni themselves. And from everything I read as long as the cause of failure isn't the user's fault Koni seems to be very cooperative. Please direct future questions to [email protected] thanks.

Edit: Missed the first question. Yes you'd need a tiny (iirc ~1mm) sleeve in the front to perfectly center the 2 washers... I was just going to use some o-rings. In the back as mentioned you need to figure out your own mounting solution, pretty easy to do with either stock mounts or an aftermarket pillowball unit like Tein.

[yudalicious]

wish I could afford, nice stuff.


Hah. Since there doesn't seem to be a flood of interest the price is negotiable with reasonable offers.

[yudalicious]

Where were you a year ago? Nice setup and good find for anyone looking for a quality performance suspension. Kicks the crap out of most of the Japanese coilovers out there.

I hate to sell them but the 240 is really old and I gotta put money towards a more reliable DD... They won't dump your car but they should be great.....

[yudalicious]

BUMP price negotiable please email thanks.

[yudalicious]

BUMP. Price lowered to $900 plus shipping. This is a helluva deal.

[racerx2k1]

Hah. Since there doesn't seem to be a flood of interest the price is negotiable with reasonable offers.

BUMP price negotiable please email thanks.

BUMP. Price lowered to $900 plus shipping. This is a helluva deal.

2 bump limit. You can start new thread in 3 days.