Drop in an RB25!!! xmembers/driveshaft $250

[mr.booie]

located in Palmdale, CA, 93551

NO SHIPPING

$250 FIRM

i have an engine and tranny crossmembers along with a driveshaft for the rb25/s13 swap. the driveshaft will only work with an RB25, and the xmembers will work with an RB25 or RB20.

the driveshaft is made from 4130 steel tubing and Spicer REPLACEABLE u-joints that can handle over 800hp. Cost over $440 new.

the xmembers were custom made by cullen at garageworks.ltd in Lancaster. (he charged $700 for them to be made.)

the xmember will only need stock skyline motor mounts and tranny mount then it will be complete and will mount perfectly into your s-chasis.

http://i282.photobucket.com/albums/kk255/sterlingro/CIMG0176.jpg

http://i282.photobucket.com/albums/kk255/sterlingro/CIMG0177.jpg


actual pic of motor using this kit:
http://i282.photobucket.com/albums/kk255/sterlingro/rb.jpg

[mr.booie]

bump #1...

[!!chuy!!]

u selling the tranny?

[palmdale_mob]

Bump for a legit seller and great price!

[brewster240]

isnt that a stock r33 crossmember? and a cut and welded s13/14 trans xmember?

someone charged you 700 for that and told you it was custom?

[mr.booie]

u selling the tranny?

nope

isnt that a stock r33 crossmember? and a cut and welded s13/14 trans xmember?

someone charged you 700 for that and told you it was custom?

no this is a s13/r33 crossmember. the two engine crossmembers from an s13 and r33 were combine to make this. (it would also work in an s14.) it does the same exact thing as Mckinney mounts, but at a fraction of the price.

yes it did cost $700 to make and install. but the previous owner of these payed that.




i guess this counts as my 2nd bump.

i am also open to trades

[brewster240]

the only thing different about s13/14 crossmember, and r33 is the motor mount "pads"....
the spine is the same, so if he put r33 "pads" on a 13/14 crossmember, its still the same thing as a r33 crossmember.

please show what is different about this?

stock r33 crossmember, which looks exactly the same:
http://photos-e.ak.facebook.com/photos-ak-sf2p/v357/195/103/1465020244/n1465020244_30164924_6965.jpg

[Tenchuu]

wow someone got shafted, but the price is cheap for all this stuff, sometimes hard to find too.

[brewster240]

the driveshaft will only work with an RB25, and the xmembers will work with an RB25 or RB20.



also, the rb20 and rb25 use different crossmembers/mounting brackets.

to use this with 20, youd need the 25 engine brackets, or you would just use a r32 crossmember

and the rb20 uses a different trans, which would bolt up to stock 240 trans xmember using r32 xmember.

so if you are using a rb25 trans behind a rb20, then yes, this trans x member would work, but not with 20 trans.

[mr.booie]

the only thing different about s13/14 crossmember, and r33 is the motor mount "pads"....
the spine is the same, so if he put r33 "pads" on a 13/14 crossmember, its still the same thing as a r33 crossmember.

please show what is different about this?

stock r33 crossmember, which looks exactly the same:
http://photos-e.ak.facebook.com/photos-ak-sf2p/v357/195/103/1465020244/n1465020244_30164924_6965.jpg

also, the rb20 and rb25 use different crossmembers/mounting brackets.

to use this with 20, youd need the 25 engine brackets, or you would just use a r32 crossmember

and the rb20 uses a different trans, which would bolt up to stock 240 trans xmember using r32 xmember.

so if you are using a rb25 trans behind a rb20, then yes, this trans x member would work, but not with 20 trans.

Thanks for helping my financial situation with these great comments. Ill see you in 3 days when i can post another thread.:kiss:
:lockd::lockd:

[brewster240]

thanks for trying to mislead unsuspecting buyers in order to fill your pockets.

granted, its not a bad price for the parts, but why try to mislead people?

in the pm you sent me, it sounds like you are aware that its not a custom crossember.

[mr.booie]

thanks for trying to mislead unsuspecting buyers in order to fill your pockets.

Granted, its not a bad price for the parts, but why try to mislead people?

In the pm you sent me, it sounds like you are aware that its not a custom crossember.

ok. I did not say anything about it not being a custom crossmember. If you are not interested in buying my parts then do not post in this thread. Your word is going againts a professional shop owner's work. Cullen at garageworks.ltd made these. He is well known out here. Please leave the thread alone next time i make one. you are misleading people. Why are you going out of your way to insure that i dont sell my parts???

lock this $#!+ so i can make a new one in 3 days...