DrifterProdigy85
08-19-2009, 05:42 PM
http://i139.photobucket.com/albums/q282/KB240SR/240sx016.jpg
Engine
SR20DET Redtop
CP Pistons 86.5mm 9.0 CR
Golden Eagle Sleeves
Manley Turbo Tuff Rods
Calico Coated ACL Race Bearings
ARP Main Studs
Balanced & Polished Crankshaft
ATI Crank Pulley
Q45 Throttle Body
Greddy Oil Pan
Greddy Intake Manifold
Kazama Solid Engine Mounts
24x12x4 FMIC
Apexi Intake
Z32 MAF
Head
Ported & Polished
Polished Compression Chamber
Full Radius Valve Job
Apexi 1.5mm Headgasket
Tomei/HKS Adjustable Cam Gears
Tomei Solid Lifters
Tomei Solid 270 Cams
Brian Crower Valve Springs
Brian Crower Titanium Retainers
Turbo/Exhaust
Garrett T67 DBB Turbo
Hybridynamics Top Mount Manifold
Hybridynamics Downpipe
Fuel System
Deatschwerks 740cc Injectors
Nismo Fuel Pressure Regulator
Summit Fuel Pressure Gauge
Engine Management
Best1Tuning Tuned ECU
Drivetrain
Nismo Tranny Mount
B&M Short Shifter
Toda Flywheel
Exedy Stage II Clutch
Project Nissan Clutch Line
I want to sell as a whole S13 ready to swap setup. Block work was done by Mazworx and have the documentation to prove it. Head was done by Spicer Motors which is a long time hotrod builder and does excellent work. Last time dynoed it made 502whp on 93 octane. Since then i have put on a Q45 Throttle Body which has helped a ton in airflow over the entire rev band. This is for sure a 600+hp @ flywheel. My asking price is $5000. There is over 10k in parts alone with this setup.
Engine
SR20DET Redtop
CP Pistons 86.5mm 9.0 CR
Golden Eagle Sleeves
Manley Turbo Tuff Rods
Calico Coated ACL Race Bearings
ARP Main Studs
Balanced & Polished Crankshaft
ATI Crank Pulley
Q45 Throttle Body
Greddy Oil Pan
Greddy Intake Manifold
Kazama Solid Engine Mounts
24x12x4 FMIC
Apexi Intake
Z32 MAF
Head
Ported & Polished
Polished Compression Chamber
Full Radius Valve Job
Apexi 1.5mm Headgasket
Tomei/HKS Adjustable Cam Gears
Tomei Solid Lifters
Tomei Solid 270 Cams
Brian Crower Valve Springs
Brian Crower Titanium Retainers
Turbo/Exhaust
Garrett T67 DBB Turbo
Hybridynamics Top Mount Manifold
Hybridynamics Downpipe
Fuel System
Deatschwerks 740cc Injectors
Nismo Fuel Pressure Regulator
Summit Fuel Pressure Gauge
Engine Management
Best1Tuning Tuned ECU
Drivetrain
Nismo Tranny Mount
B&M Short Shifter
Toda Flywheel
Exedy Stage II Clutch
Project Nissan Clutch Line
I want to sell as a whole S13 ready to swap setup. Block work was done by Mazworx and have the documentation to prove it. Head was done by Spicer Motors which is a long time hotrod builder and does excellent work. Last time dynoed it made 502whp on 93 octane. Since then i have put on a Q45 Throttle Body which has helped a ton in airflow over the entire rev band. This is for sure a 600+hp @ flywheel. My asking price is $5000. There is over 10k in parts alone with this setup.