FS: Sweet JDM Garage Sale *Offers Welcome*

[tig_tech]

Location: Jacksonville, FL

Payment: Cash, Paypal, Check,

Email:[email protected]

Parts are used unless otherwise stated.

S13 SR20DET Greddy Coldpipe for stock intake manifold (Great Condition) $55obo
http://i43.tinypic.com/dm8e44.jpg

S13 Oil Strainer w/O ring(Brand New)$35obo
http://i41.tinypic.com/2j2vkv5.jpg

Greddy Oil cooler kit w/relocation minus the cooler(Great Condition)$200obo
I have a diagram for proper installation, you just need an oil cooler!
http://i32.tinypic.com/k2mlbq.jpg
http://i31.tinypic.com/xlh5s1.jpg

S13 SR20DET Loaded Cylinder Head(Good Condition)$180obo
http://i25.tinypic.com/1zxtweu.jpg

Twin Revcor Electric Fans(Good Condition)$30obo
http://i28.tinypic.com/106m0zo.jpg

S13 SR Valve Cover-Semi Polished need to be buffed(Great Condition)$50obo
http://i28.tinypic.com/wbxch1.jpg

S13 240sx Aero Mirrors with LED(Great Condition)$35obo
http://i32.tinypic.com/112dhs3.jpg
http://i27.tinypic.com/2cwqvc0.jpg

Various Brand New SR20DET Gaskets/Seals/Orings(Brand New)PM for pricing
http://i29.tinypic.com/2ed73w5.jpg

Zap Medium Pro Skimboard(up to 180lb rider)-$130obo
http://i32.tinypic.com/jfl0km.jpg

[zac 3ne2nr]

will the relocation and filter kit work with an RB20?
is this chassis specific also, in terms of routing and length?

[MrFairlady]

Not to Hijack - But You can basically use the Regular Greddy Relocate as a Cooler kit also??
so ALL i need is to switch to AN Lines (from the Nipple Ends) and a thermo and a Cooler Core YES??

nice set up.
Worked Well for you?

[tig_tech]

zac- this is chassis specific for an S13. Now with the RB20 im not too sure where the oil block on the engine sits in comparison to the SR20 oil block. Might not be much of a difference but if anything you may need to extend or cut lines.

MrFairlady-Yes you can in a way but its going to cost more money doing it that way because those fittings are very expensive as well as the cooler, and a thermostat. With my kit all you need is the cooler and your good to go. Plus the oil block that comes with this kit include npt fittings for temp/pressure sensors.

The setup is awesome. Im just changing setups right now.

[zac 3ne2nr]

Thanks man, its a a good buy for a direct application. I don't want to hack it up.

[International B]

pm sent about the fans

[tig_tech]

Thanks man, its a a good buy for a direct application. I don't want to hack it up.

Yea thats true. But if you know your way around earls fitting and lines it would be no problem.

[tig_tech]

to the top

[zac 3ne2nr]

Hmm. ok I'm really liking this. Clarify soemthing for me please.
This is the one I found but the filter adapter has two other ports for a total of 4.
How is your cooler fed?
http://www.skylinesaustralia.com/forums/post-a191453-

[tig_tech]

Mine is a 5 hose setup and the one you pictured is a 4 hose setup. 1 hose comes from the center of the block adapter on the engine into the relocation block that gets mounted on the shock tower, out from that, into the thermostat, out from that, into the cooler. Then the out from the cooler into the thermostat, out from that, into the oil block on the engine.

Yours is basically two out from the block into the 4 port adapter and two out from the 4 port adapter and into the cooler.

[frost1988]

30 shipped for the strainer pm me

[tig_tech]

Last bump before starting new thread.

[NMs14.5kouki]

you willing to part out just the block adapter?

[tig_tech]

No sorry I cant. Need to sell as a kit only.