Built RWD SR20DET

[91 240]

I’m parting out my current setup and going with something completely different. This is my fully built SR20DET with only 1100 easy break in miles. Motor has never seen boost and has solid 160psi compression and 2% leak down across all 4 cylinders. Motor is built for 600 whp! Here’s the build list and everything included:

Aftermarket parts
S13 redtop motor
Apexi cylinder sleeves
Crower rods (not Brian Crower)
CP 87mm pistons 8.5 compression
ARP main studs
ARP head studs
Greddy oil pan
Cometic MLS head gasket
Comp Cams valve springs
HKS 272 step 2 cams
Greddy rocker arm stoppers
MMR polyurethane motor mounts
ACT 6 puck clutch kit

New OEM parts
Main bearings
Rod bearings
Thrust bearings
Front cover/oil pump and front main seal
Water pump
Timing chain and crank gear
Updated timing chain guides
Timing chain tensioner
Rear main seal
Valve stem seals
Water temp sensor

Machine Work
Balance/polish crank
Balance rotating assembly
Sleeve install/bore/hone
Align hone mains
Decked block and head
5 angle valve job

Other accessories and items included
CAS
Alternator
Starter
Coil packs
Power steering pump with DOHC s13 reservoir
Autometer oil temp sender in oil pan
Coolant temp cluster gauge sender removed and tapped for Autometer 1/8 npt sender
Stock oil pressure sender removed and has Autometer 1/8 bspt ->1/8npt fitting
Heater hose hard lines have nipples removed and welded shut
Stock PCV removed and -10AN fitting has been welded to valve cover for crankcase evac

$4000 plus shipping

Please PM or email at [email protected] if interested or for any questions.

http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/sleeves.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/PISTONKIT2.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/crowerrods.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor002.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor003.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor005.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor006.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor004.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor008.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor014.jpg

[ross.cottrill]

damn man thats a good deal.if you were only 2 weeks earlier i would have bought this from you but ive already started on my block/head.glwts!!

[91 240]

still for sale

[91 240]

last bump guys

[reccakun08]

question, why did u have the "Heater hose hard lines have nipples removed and welded shut"?

[91 240]

price drop to $3800 plus shipping. any takers?

[heiyuu]

question, why did u have the "Heater hose hard lines have nipples removed and welded shut"?

this. ???????????

[91 240]

this. ???????????

i removed the coolant lines to clean up the engine bay and had the hard line nipples capped off. the caps started to dry out and leak. i then had the nipples cut off and welded shut to make things easier.

[lazysk8er2]

had the nipples cut off and welded shut to make things easier.


sounds painful but interesting

[91 240]

open for any reasonable offers

[racerx2k1]

still for sale

last bump guys

price drop to $3800 plus shipping. any takers?

open for any reasonable offers

2 bump limit. You can start new thread in 3 days.