PDA

View Full Version : CA Custom SR20 Shim Tip Height Tool

johngriff
03-20-2009, 11:18 AM
If you have read your FSM, or had rocker arms pop off/ break / crack / lost engines then you might know what I am talking about.

The Nissan Special Service Tool is about $700 and does not work as well as this tool does.

This is put together custom and using a digital gauge. Simply Zero it out on the Guide side, then measure against on the shim and adjust accordingly.

If you have VALVE NOISE, put new cams in, new valve springs, had a recent valve job etc etc this is the tool to cure all of your woes.

This is ready to go to you for $90 Picked up in Long Beach, or $99 shipped in the US.

Paypal to confirmed addresses only!

John
[email protected]
johngriff
03-20-2009, 11:45 AM
http://i32.photobucket.com/albums/d2/vonendorphin/More%20Zilvia/CS_Tool_1.jpg


Here is a picture of the tool
johngriff
04-02-2009, 01:44 PM
Bump for the week.

No one Needs this tool? Never heard of its use?
xvr420x
04-02-2009, 02:13 PM
can i borrow it?
johngriff
04-02-2009, 03:28 PM
Lol, just buy it.

Write me: [email protected]
georgesal
04-04-2009, 12:01 AM
hey john i might buy this give me a call if you stil have this friday
Slideways^Jordan
04-04-2009, 12:15 AM
pm sent i need your paypal address please.

Thanks
Jordan
s13silvia123
04-04-2009, 01:02 AM
oh john you got the coolest shiiit made all the time
johngriff
04-04-2009, 12:15 PM
I got back at smelly and jordan with paypal info.

George, we will see if I still have it next week.

John
Slideways^Jordan
04-04-2009, 03:45 PM
I got back at smelly and jordan with paypal info.

George, we will see if I still have it next week.

John

I sent you another pm. Thanks
johngriff
04-04-2009, 03:48 PM
Sold Pending E-Check clearing
johngriff
04-04-2009, 04:41 PM
Sold!

Thank you!

John
Slideways^Jordan
04-04-2009, 04:50 PM
haha crazy echecks lol.

Thanks John and for all the help.

I will enjoy the tool very much and take great care of it.
djcobra
04-04-2009, 06:46 PM
damn! you have another one like this?

Steve.
georgesal
04-04-2009, 06:50 PM
hey john call me lost your new number, i have a question
johngriff
04-05-2009, 12:13 PM
I have another HLA Post that this tool is based off of.

I "Could" make another one, but its going to cost you ($150) b/c I can't find the aluminum stock in the garage, and I will have to purchase it, then machine it. Then go get another gauge.

So if you are serious, put your money where your mouth is.
moses
04-15-2009, 09:46 PM
If you were to make me one I would buy it for 150 if you are for sure it will be accurate
johngriff
04-15-2009, 09:57 PM
Ok, hit me up.

Yes, very accurate. Used the first tool on a ton of cars.

Call me for my paypal.

John
johngriff
07-01-2009, 01:05 AM
Hey! Everyone who was interested in these.

http://www.rpsport.net/vsht/gauge2s.png

I made two now by request, and purchased enough material to make about 20 more.

This is going to be a limited run of this tool.

Also Included is a 6 page instruction/workshop booklet I wrote, on taking these measurements, and using the tool to auto calculate your shims.

I will also leak the Instruction manual for a few days:
http://www.rpsport.net/support/vsht/instructions.pdf

on the site!

RPSport.net Welcome (http://www.RPSport.net)

[email protected]
racerx2k1
07-01-2009, 06:05 AM
http://zilvia.net/advertise.html