FS: Complete SR20det Setup & Part out

[90rps13]

Selling an sr20det redtop complete long block (valve cover to oil pan). Asking for $600. Never had any issues with the motor, it's always been reliable for me. Completely stock. Never tracked the car with this motor. The reason I dropped the price from $700 to $600 is because while I was putting the stock cams back in (previously had BC cams)... One of the cam bearing cap bolts broke. Of course it had to be the last screw that I was putting on. Anyway, everything is buttoned down nice and tight, to spec. Someone just needs to drill out the 10mm bolt and put a new one in. I don't have the time nor a drill to do this. Should be fairly easy as these normally screw in by hand. Has a fairly new water pump on it. Anyway, asking $600 for it. Many have asked if it includes turbo, or ecu, or..whatever... Again, price is for LONG BLOCK only...

Other parts sold separately:

BC 264 Cams - SOLD
Lightened Pulleys - SOLD
RAS - SOLD
JWT 550cc top feed injectors - SOLD
Nismo FPR - SOLD
Megan Headers - SOLD
Stock T25 - SOLD
Circuit Sports Turbo Elbow/Downpipe Combo - SOLD
Greddy FMIC v-spec w/ piping - $390 firm
Hotpipe w/ Greddy BOV - $125
Westco Slim Battery - $55
Alternator - $65
Starter - $60
Z32 MAF - SOLD
Suction Intake Piping - SOLD
Blitz SUS Intake Filter (Metal Mesh) - SOLD
Nismo Motor Mounts (Good condition) - SOLD
Koyo Radiator - SOLD
Test Pipe - $30
Turbonetics Boost Controller - SOLD
Greddy Turbo Timer - $55
Igniter - $75
Coil Packs (Set of 4) - $150 or $40 each
Coil pack cover - $15
Cam Angle Sensor - $120
Throttle body with good TPS - $40
RPS clutch - $70 (Still has plenty of meat left on it...)
T28 inlet and outlet adapter to use T25 piping - $60
Fat o2 sensor (6 months old) - $50
Clutch Fan - $15
Blown BB T28 with waste gate - $50 firm

Other things included with the motor/tranny:
RPS 6 Puck Clutch (Good for about 400hp)
Wiring Harness (Completely stripped down and re-wrapped)
ECU with Rom tune for 550 injectors/Z32 MAF

I don't want to part out the long block just yet, but I will sell the complete long block (valve cover to oil pan) for $700.

Tranny for $350 (Shifts perfectly, no grinding at all)

ECU #62 - SOLD

Wiring harness - $200

Think that's about it. These are all picked up prices and are obo... I can be reached at 626.329.8425 or [email protected]

http://www.mydesignwork.com/SRparts/SR20.jpg

http://www.mydesignwork.com/SRparts/tranny.jpg

http://www.mydesignwork.com/SRparts/fmic.jpg

http://www.mydesignwork.com/SRparts/cams.jpg

http://www.mydesignwork.com/SRparts/harness.jpg

http://www.mydesignwork.com/SRparts/clutch.jpg

http://www.mydesignwork.com/SRparts/coils.jpg

http://www.mydesignwork.com/SRparts/pulleys.jpg

http://www.mydesignwork.com/SRparts/clutch_fan.jpg

http://www.mydesignwork.com/SRparts/o2.jpg

http://www.mydesignwork.com/SRparts/westco.jpg

http://www.mydesignwork.com/SRparts/alt.jpg

http://www.mydesignwork.com/SRparts/t28.jpg

http://www.mydesignwork.com/SRparts/tb.jpg

http://www.mydesignwork.com/SRparts/coils_cover.jpg

[wideride]

im interested on koyo radiator. what your best price?

[beyondstock]

You going to sell those coilovers?

I'll take wiring harness and N62 if you'll take 250 shipped

[chris300zr]

interested in harness. Sent you a PM.

[brian3676]

$225 shipped to 97229 for cams and CS downpipe/dump tube combo?

[90rps13]

Coilovers are already sold. PM's sent back to everyone...

[VNG704]

Who tuned the ecu? Willing to let go 550cc injectors, tuned ECU, and Z32 MAFS for $400 shipped? PM me.

[90rps13]

Who tuned the ecu? Willing to let go 550cc injectors, tuned ECU, and Z32 MAFS for $400 shipped? PM me.

Gentlemen by the name of Aki through Monstor Fabrications. This is the guy that tuned Casper Canul's S14. He's really good. He was able to extract 320whp from this motor and could have gone more, but the clutch started slipping. I upgraded the clutch but never went back to re-tune...

PM Sent...

[bl3ujay07]

damn, if you would have posted up sooner before i bought the circuit sport elbow, i would have bought the elbow/downpipe from you right away!!! hm... trade my less than 10 mile elbow + cash on my end for the elbow downpipe combo??? LMK intereted.

[VNG704]

Want to show the print out of the 320 whp dyno pull? What are the specs of the tune besides the actual tuning: raised rpm, max speed, etc..?

[90rps13]

Want to show the print out of the 320 whp dyno pull? What are the specs of the tune besides the actual tuning: raised rpm, max speed, etc..?

I don't have that available... Long story...

[s13sr20-silvia]

how much shipped to 98433?

[90rps13]

how much shipped to 98433?


What, the whole settup? Not shipping the motor or trans...Sorry.

[speedgod^s13]

Who makes that suction intake piping?

[90rps13]

Who makes that suction intake piping?

Don't know the brand, but it's like KTS style...

[babohyungjin]

$220 picked up for circuit sports combo+intake combo?

[90rps13]

$220 picked up for circuit sports combo+intake combo?

PM sent...

[s13driftnut]

i'll take that boost controller off your hands, pm me please

[90rps13]

i'll take that boost controller off your hands, pm me please

Sold!!!!!!!

[90rps13]

More items added and prices dropped...

[besTint]

what happened to the motor? why was it pulled?

[90rps13]

what happened to the motor? why was it pulled?

Nothing happened to the motor, I just wasn't able to get what I wanted for the complete car. As we all know, we'll never get what we put into it back. This is my 3rd 240 and I'm just done with them for now. Moving on to another project.

[gospdracer90]

how much for the clutch

[90rps13]

how much for the clutch

Everything should list price in the first post above. Clutch is $70 picked up...
Thanks

[tf_90s13]

is the stater still available if so is it for a rwd. if it is let me know. im local west covina.

[racerx2k1]

4 month old thread.