RMJmotor
02-16-2009, 05:14 PM
Guys I have the full Haltech E6X setup off my old Pro AM Drift 240sx starting to part the car out as the car did not sell as a whole.
*** I Accept Cash and Paypal. I will ship, AT BUYER EXPENSE. ***
This is a Full stand alone unit and will need to be reprogramed for your Sr20DET setup.
$1125.00 SHIPPED (to lower 48 states) **if you pay by PAYPAL please add 3%**
This setup is complete, pre-wired for the SR20DET Redtop. Includes the following:
- Haltech E6X stand alone ECU
- Full flying lead Harness pre-wired for SR20DET redtop w/ side feed injectors. Will fit stock TPS/ temp / Cam sensors
- LS1 Coils (This will not work with stock SR20 Coils unless re-wire) LS1 coils are much stronger than the stock coils.
- Custom made 8.5mm Magnacor spark plug wires. Made for LS1 to Sr20 Plugs
- 3-bar Map sensor
- Haltech Fuse block
- Air intake temp sensor
http://c3.ac-images.myspacecdn.com/images02/35/l_48a10fc2e3b44b8d8a2a491e5079db16.jpg
http://c3.ac-images.myspacecdn.com/images02/24/l_da6bb6c7cfc1490bb8251177ba6cb96a.jpg
This is the Haltech installed in he car:
http://c1.ac-images.myspacecdn.com/images02/9/l_e80c64f445224e18b510f088587fda78.jpg
Basically just ditch you old harness and ECU, run the new harness, run power and ground to ECU and Fuel pump. Plug in the injectors, coils and sensors, program, and go.
I will ship, Retail on this ECU is over 1300.00 and that does not include having the harness made and wired or installation, LS1 coils new are about 200 and you need to wire and make the cables.
$1125.00 SHIPPED (to lower 48 states) **if you pay by PAYPAL please add 3%**
Contact me with any Questions.
*** I Accept Cash and Paypal. I will ship, AT BUYER EXPENSE. ***
This is a Full stand alone unit and will need to be reprogramed for your Sr20DET setup.
$1125.00 SHIPPED (to lower 48 states) **if you pay by PAYPAL please add 3%**
This setup is complete, pre-wired for the SR20DET Redtop. Includes the following:
- Haltech E6X stand alone ECU
- Full flying lead Harness pre-wired for SR20DET redtop w/ side feed injectors. Will fit stock TPS/ temp / Cam sensors
- LS1 Coils (This will not work with stock SR20 Coils unless re-wire) LS1 coils are much stronger than the stock coils.
- Custom made 8.5mm Magnacor spark plug wires. Made for LS1 to Sr20 Plugs
- 3-bar Map sensor
- Haltech Fuse block
- Air intake temp sensor
http://c3.ac-images.myspacecdn.com/images02/35/l_48a10fc2e3b44b8d8a2a491e5079db16.jpg
http://c3.ac-images.myspacecdn.com/images02/24/l_da6bb6c7cfc1490bb8251177ba6cb96a.jpg
This is the Haltech installed in he car:
http://c1.ac-images.myspacecdn.com/images02/9/l_e80c64f445224e18b510f088587fda78.jpg
Basically just ditch you old harness and ECU, run the new harness, run power and ground to ECU and Fuel pump. Plug in the injectors, coils and sensors, program, and go.
I will ship, Retail on this ECU is over 1300.00 and that does not include having the harness made and wired or installation, LS1 coils new are about 200 and you need to wire and make the cables.
$1125.00 SHIPPED (to lower 48 states) **if you pay by PAYPAL please add 3%**
Contact me with any Questions.