power fc boost kit install question

[SoguRacing]

ok guys. i just purchased an apexi boost controller setup for my l-jet setup. I was in the process of installing the solenoid and the solenoid harness and i realized that i had nowhere to plug in the solenoid harness. the pressure sensor plugs in fine to the power fc but where do i plug in the actuator harness? there male connector with a horizontal and a vertical plug inside. where/what do i do with this?

[Sileighty_85]

im in the same boat
The instruction are very vauge they tell you HOW to wire it in but not really WHERE to wire it too.

I've been thinking, it would make sense to wire it to the stock W/G harness seeing that we still use the the stock engine harness.

But ive been unable to confim it so far.

[SoguRacing]

soo, where is the stock wastegate harness and what does it look like?

[S14DB]

Crap I have a race harness and was going to buy the boost kit. The stock WG wires are gone in my harness.

[SoguRacing]

so what does the stock wastegate harness connector look like? pics?

[S14DB]

It plugs in over by the PS rez. I believe it's on the harness with the Ignitor and O2 sensor.

I'm just not looking forward to running new harness wires...

[SoguRacing]

Ok. so i just got off the phone with APEXI and the harness clip for the solenoid is supposed to plug into the engine harness for the stock wastegate solenoid. Sometimes that part of the harness is not transfered when people swap the engines so you need to take the new solenoid wires and solder them go the ecu.
As follows:
pink wire from new solenoid harness solders to pin 111 on ecu which is color orange/black.
brown/black wire from new harness solders to ecu ground wire.

[Sileighty_85]

Ok. so i just got off the phone with APEXI and the harness clip for the solenoid is supposed to plug into the engine harness for the stock wastegate solenoid. Sometimes that part of the harness is not transfered when people swap the engines so you need to take the new solenoid wires and solder them go the ecu.
As follows:
pink wire from new solenoid harness solders to pin 111 on ecu which is color orange/black.
brown/black wire from new harness solders to ecu ground wire.

I thought So

But thanks for the confirmation, I'd give ya rep if I could

so what does the stock wastegate harness connector look like? pics?

Its a Two pin box style connector
Like S14DB said It next to the Ignitor

Heres some Crappy Pics of it
http://i73.photobucket.com/albums/i235/Neil_85/PIC-0217.jpg

one wire is Orange with a black stipe, and the other one is Orange with a silver band
**Instructions say it DOES NOT matter which way you wire it**
http://i73.photobucket.com/albums/i235/Neil_85/PIC-0218.jpg

[Mirage]

S14's plug doesn't look like that, its a 2 pin connector also, but one horizontal, one vertical, i'll try and take a pic tomorrow. It should be right by the coilpack plug as stated before

[garagelu]

If anyone needs that boost solenoid, I have one. It will comes with the male and female part of the connector along with the pigtail on the harness side. Email me at [email protected] or PM for pics and price.

In addition its from a s13 harness. Its orange/black and brown on the harness side. And then black and white on the solenoid side.

[Sileighty_85]

S14's plug doesn't look like that, its a 2 pin connector also, but one horizontal, one vertical, i'll try and take a pic tomorrow. It should be right by the coilpack plug as stated before

Oh right My pics are from my S13

[SoguRacing]

I dont have the plug that looks like that. also, it doesn't appear that one prong horizontal and the other is vertical.

[S14DB]

For me those connectors were deleted when I had the ignitor moved next to the ECU. Guess it's time to break out the pinout diagram and wire one up.

[SoguRacing]

ok guys I did some more researching and found this ecu pin layout for the SR #62 ecu. you take pin 111 ( color orange with black stripe ) which is the 3rd wire on the bottom left of the ecu and section with 16 wire pins, and solder the apexi solenoid (red) wire to it and the solenoid brown wire to the ground wire on the ecu. said and done.