Roush 18x9 +28 5x114, retarded cheap.

[driftingpanda]

***SOLD!!!******SOLD!!!******SOLD!!!******SOLD!!!* **

Hello Guys/Gals,

DESCRIPTION:
I have a set of Roush wheels up for grabs. They're 18x9, +28 offset all around, 5x114 bolt pattern. These are OEM-quality high-pressure cast wheels (NOT your typical aftermarket low-pressure cast wheels). They were previously sand blasted and the "Roush" logos were machined off, and they're ready for polishing or new paint/powder coat.

CONDITION:
They are a bit dirty, and have some minor curb marks on three of the wheels. No deep curb checks or bends at all. All curb rash marks are easily removable with a file and sandpaper before polishing or paint.

TIRES:
Rear tires are Federal 595's in 225/40/18, one tire is bald on the inside, the other has some chunking in the middle of the tread. Both are OK to roll on. Front tires are gone, but I will toss in a pair of Federal 595's in 215/35/18, with about 50% tread left.

PRICE:
***SOLD!!!***These sell for $1200 a set new, retail is well over $2k. I'm asking ONLY $500 for the set of four WITH TIRES. ***SOLD!!!***
SHIPPING:
I will ship at buyer's expense, but WITHOUT the tires. Shipping to the continental 48 states is $130. So $630 shipped, no tires. ***SOLD!!!***

CONTACT:
Email is highly preferred: chienwec*at*hotmail*dot*com
Paypal OK.
Wheels located in Chino Hills, CA (91709)

PICTURES:
What these wheels COULD look like if polished/painted:
http://www.twintorino.com/images/texas_roush_wheel.jpg
http://jeffspowdercoating.org/gallery/albums/userpics/normal_roush_wheel_mirror_black.jpg

On the back of my s13 with slightly pulled fenders, no spacers:
http://img.photobucket.com/albums/v189/driftingpanda/wheelsforsale/n634465441_4627129_8150.jpg

Taken as of today:
http://img.photobucket.com/albums/v189/driftingpanda/wheelsforsale/PB030028.jpg

Size and offset stamp:
http://img.photobucket.com/albums/v189/driftingpanda/wheelsforsale/PB030033.jpg

Machined off logos:
http://img.photobucket.com/albums/v189/driftingpanda/wheelsforsale/PB030034.jpg

Minor curb marks (has some on 3 of the 4 wheels):
http://img.photobucket.com/albums/v189/driftingpanda/wheelsforsale/PB030029.jpg
http://img.photobucket.com/albums/v189/driftingpanda/wheelsforsale/PB030030.jpg
http://img.photobucket.com/albums/v189/driftingpanda/wheelsforsale/PB030032.jpg


-danny

***SOLD!!!******SOLD!!!******SOLD!!!******SOLD!!!* **

[driftingpanda]

Got a couple of flakers over the weekend. Need these gone. First to show up with $400 will take them with no tires.

-danny

[maxim240sx]

will these bolt right up on s14 W/O fender mods?

[FaLKoN240]

Even if they did it wouldn't be worth his or your time to ship, these wheels are probably mad heavy.

[driftingpanda]

Yes, they should fit with no fender mods. I'm not 100% sure on coilover clearance up front though, you might want to double check that.

And yes, I am willing to ship. Shipping fee is listed in my original post above. Same rate for all 48 continental states. If it ends up costing more I will eat the extra costs.

-danny

[driftingpanda]

Multiple buyers flaked. Price drop to $350. Get 'em while they're hot!

-danny

[5t341tH]

dude thats retarded cheap. let me tell my frend

[OTG Vinyl]

Not a bad price! I've had six Mustangs and have seen these go for much much more!

[vodka2]

awsome wheels !!
free bump.

[essforteen]

great seller buy his wheels!!

[Dee]

If I can track down some 5lug hubs for a good price then these are mine!

[driftingpanda]

Somebody with a screen name of s14xxxxxx? PMed me about these, but I deleted it by accident. Let me know if you're still interested.

Still up for grabs. First-come, first serve!

BTW these are high-pressure cast wheels, and are lighter than your average cast wheel. Still have the tires on them though, so I can't get an actual weight on these.

-danny

[driftingpanda]

OMG I can't believe I still have these in the backyard. Since a couple of people requested it, here's a few new pictures for you guys that may be on the fence about these. They're pretty flush with the right camber (about 1.5 degrees), and all you'd need is a fender roll with no pull, and they'd be pretty nice for a daily or as drift spares.

http://img.photobucket.com/albums/v189/driftingpanda/wheelsforsale/103_0849.jpg
http://img.photobucket.com/albums/v189/driftingpanda/wheelsforsale/103_0853.jpg
http://img.photobucket.com/albums/v189/driftingpanda/wheelsforsale/103_0857.jpg

[Tandem Hero]

I just got a new job. Once I get paid I'll pick these up. Still same price shipped?

[lukebaumstark]

pm'd ya danny

[driftingpanda]

Tandem Hero: yeah dude, shipped price is still $480. First come, first serve. My paypal is the same as my email posted above.

[logik23]

Do you know the hub bore size???

Why would anyone machine off the logo? lol

If anyone knows something about rim repair, would it be possible to fill in the indentation where the logo was??

[driftingpanda]

logic23: i don't know the bore size, but i'm sure you could google it. i had it on my s13 so i know it clears s-chassis bore size at least. i had the logo machined off because i wanted to run a sticker. if you wanted it filled, you could get it welded up with aluminum and grind/sand it flat. i'm sure you could fill it with some bondo, but i can't say for sure how long that'd last.

[logik23]

So tempted....I wanna put these on my Jeep......but the bore size is slightly bigger....

Did the hub fit flush on the S13?

My center bore is 71.5mm and an S13 is 66.2....................

[Sil-Eighty SE-K]

howd i miss this? dammit..... the 18x9.5 +12 are gonna be a bitch to fit.... these woulda been easier

[kpc_0721]

Hey do you have any idea what year car these came off of?

[KT-Lex]

These aren't from the new Mustangs. I just seen a new model Mustang with these wheels and they didn't look like these. Very similar but not the same.
For an extra 400.00 bucks these would look very clean

[FaLKoN240]

Hey, I'm just wondering how much these weigh...?

Are they heavy like most domestic wheels (20lb +?)

Let me know.

[driftingpanda]

logik23: If you're really interested, shoot me a PM and I'll measure the actual bore size for you.

kpc 0721: Not sure what year these came off of. Since they're Roush wheels they're technically aftermarket, but were considered OEM since they were sold off the showroom floor. Might want to check with Roush to find which years they used these.

Falkon240: No idea on the weight. The tires are still on the wheels so I can't weigh them. They seem like standard weight for an 18x9 wheel, but I can't confirm. These were high-pressure cast, meaning they'd be lighter than your standard low-pressure cast wheels of the same overall volume. They're not super light like forged wheels or anything.

Sale is pending to a local dude who wanted to pick these up tonight. If these get sold I will update the first post. Thanks for all the interest.

[sirfallsalot243]

$500 shipped if you tell the local to f*ck himself. :D

Let me know if they fall through, I have cash in hand.

[driftingpanda]

Sorry dudes, these just got sold to a local buyer. Haha, I posted these last year and nobody wanted them! Thanks for all the interest!