meme
10-05-2008, 03:17 AM
1986 coupe red. has sunroof, power mirrors, manual windows. gts seats.
black top ae111 39k milage.
Toda racing timing belt
New water pump
Pass racing pulley set
Sp tech dizzy relocation kit
Ultra racing spark plug wire set for the 20v
RS Chita water relocation kit
16v water setup. modified coolant hard line to route under knock sensor.
knock sensor still in stock location.
OEM 20v belt tensioner NEW
OEM 20v belt pulley NEW
solex lock set
bmw HID set
light housing for h4
T3 velocity stacks
T3 strut tower bar the triangle one. like cusco
S13 engine dampener
modded wire harness. from mr20v. cleaned up and removed unnessesary wires.
chassis harness has been modified and cleaned up. rerouted for clean looking engine bay.
SHort shifter
TRD engine mounts
cusco trans mount
chromoly flywheel 10lbs
OEM throwout bear
OEM pilot bearing
koyo radiator with custome made dual 12in fans wired up for 20v thermo switch.
greddy fuel pressure sensor
greddy 52mm white face fuel pressure gauge.
new fuel filter
all steel braided fuel line(-6) from the tank to fuel rail.
new clutch master cyl
steel braided line for clutch with -3 fittings
new brake master cyl
willwood big brake kit for the front. more then 3/4 brake pads left
rear calipers and brackets are remanufactured. only used for about 1k miles before parking and doing this swap.
tanabe swaybar front and rear
thick swaybar rod ends and bushing.
full protane kit
cusco pan hard bar(i think it is cusco)
tie rods inner and outer
new boots
crossmember, control arms,tension brackets,rear arms all hot tanked cleaned and painted.
new crossmenber bolts and bumper support bolts and a few others(all OEM)
new ball joints.
tein camber plates
eibach springs
sw20 front shocks adjustable
sw20 rear shocks adjustable
lower blocks for front shocks
cross drilled rotors and steel bradied lines, i think pbr pads.
Levin front end is all new from toyota except fenders and hood. all OEM toyota brackets for bumper and head lights.
New Tomei 2way lsd and complete rebuild of third member. axles have new bearings and seals. new wheel studs. everything in the rear end was repalce with new parts. installed 4.77 gearing as well. new part.
custom headers with flex pipe.
all parts are new unless stated used.
just finished the car last weekend. since then ive changed oil/filter,trans fluid(red line), and diff (motul90pa) and coolant flush twice. last weekend adn this weekend.
as is with bride vios lowmax seat and rail,nardi casic steering wheel, and crazy size/offset work o3 15x8.5 -6 15x9 -3 yokohama in back, azenis in front. $10,500
or without parts listed above $8600
http://wasabigarage.com/img/pics/ae86/ae111_swap/install/9_28_08/CIMG1499_1.JPG
http://wasabigarage.com/img/pics/ae86/ae111_swap/install/9_28_08/CIMG1498_1.JPG
http://wasabigarage.com/img/pics/ae86/ae111_swap/install/9_28_08/CIMG1506_1.JPG
http://wasabigarage.com/img/pics/ae86/ae111_swap/install/9_28_08/CIMG1512_1.JPG
http://wasabigarage.com/img/pics/ae86/ae111_swap/install/9_28_08/CIMG1513_1.JPG
black top ae111 39k milage.
Toda racing timing belt
New water pump
Pass racing pulley set
Sp tech dizzy relocation kit
Ultra racing spark plug wire set for the 20v
RS Chita water relocation kit
16v water setup. modified coolant hard line to route under knock sensor.
knock sensor still in stock location.
OEM 20v belt tensioner NEW
OEM 20v belt pulley NEW
solex lock set
bmw HID set
light housing for h4
T3 velocity stacks
T3 strut tower bar the triangle one. like cusco
S13 engine dampener
modded wire harness. from mr20v. cleaned up and removed unnessesary wires.
chassis harness has been modified and cleaned up. rerouted for clean looking engine bay.
SHort shifter
TRD engine mounts
cusco trans mount
chromoly flywheel 10lbs
OEM throwout bear
OEM pilot bearing
koyo radiator with custome made dual 12in fans wired up for 20v thermo switch.
greddy fuel pressure sensor
greddy 52mm white face fuel pressure gauge.
new fuel filter
all steel braided fuel line(-6) from the tank to fuel rail.
new clutch master cyl
steel braided line for clutch with -3 fittings
new brake master cyl
willwood big brake kit for the front. more then 3/4 brake pads left
rear calipers and brackets are remanufactured. only used for about 1k miles before parking and doing this swap.
tanabe swaybar front and rear
thick swaybar rod ends and bushing.
full protane kit
cusco pan hard bar(i think it is cusco)
tie rods inner and outer
new boots
crossmember, control arms,tension brackets,rear arms all hot tanked cleaned and painted.
new crossmenber bolts and bumper support bolts and a few others(all OEM)
new ball joints.
tein camber plates
eibach springs
sw20 front shocks adjustable
sw20 rear shocks adjustable
lower blocks for front shocks
cross drilled rotors and steel bradied lines, i think pbr pads.
Levin front end is all new from toyota except fenders and hood. all OEM toyota brackets for bumper and head lights.
New Tomei 2way lsd and complete rebuild of third member. axles have new bearings and seals. new wheel studs. everything in the rear end was repalce with new parts. installed 4.77 gearing as well. new part.
custom headers with flex pipe.
all parts are new unless stated used.
just finished the car last weekend. since then ive changed oil/filter,trans fluid(red line), and diff (motul90pa) and coolant flush twice. last weekend adn this weekend.
as is with bride vios lowmax seat and rail,nardi casic steering wheel, and crazy size/offset work o3 15x8.5 -6 15x9 -3 yokohama in back, azenis in front. $10,500
or without parts listed above $8600
http://wasabigarage.com/img/pics/ae86/ae111_swap/install/9_28_08/CIMG1499_1.JPG
http://wasabigarage.com/img/pics/ae86/ae111_swap/install/9_28_08/CIMG1498_1.JPG
http://wasabigarage.com/img/pics/ae86/ae111_swap/install/9_28_08/CIMG1506_1.JPG
http://wasabigarage.com/img/pics/ae86/ae111_swap/install/9_28_08/CIMG1512_1.JPG
http://wasabigarage.com/img/pics/ae86/ae111_swap/install/9_28_08/CIMG1513_1.JPG