turtl631
08-03-2008, 09:30 AM
I'm located in Chicago. Pickup preferred on coilovers, but will ship if necessary. Best contact is email- rrozyckATgmailD0Tcom
Greddy headgasket and valvesprings: I bought an SR from a local guy who was putting it in a Frontier, but his wiring job was botched and he never got spark, so it never started. He installed these parts but only turned the motor over with them.
The headgasket was torqued down properly with stock head bolts...it looks new other than a tiny scuff by one of the dowel holes. I measured it at 1.2 mm thick with an 88 mm bore, which seems to be the standard Greddy HG. $75 shipped
http://i11.photobucket.com/albums/a160/turtl631/IMG_7047.jpg
http://i11.photobucket.com/albums/a160/turtl631/IMG_7048.jpg
http://i11.photobucket.com/albums/a160/turtl631/IMG_7049.jpg
Greddy valvesprings- not much to say here, installed like the headgasket, but obviously wear is low on a set of springs that gets installed and then just sits other than being turned over a few times. $75 shipped
Crower retainers- Part number is 87097, they're just Crower titanium retainers (not BC pieces, but I don't know if there's any real difference). $75 shipped
Stance S14 GR+: These are 2.5 years old, with probably around 8000 miles on them. They have Z32 rear lower mounts, so they can only be run with Z32 rear spindles. As far as I can tell, they were made before Stance had these issues with crappy camber plates, as they haven't made any weird noises or failed in any way in the time I've had them. I'm also including the 9k and 7k springs, never used. I have the wrenches too, although they're a little bent. $700 (prefer local, but will ship)
http://i11.photobucket.com/albums/a160/turtl631/IMG_7040.jpg
http://i11.photobucket.com/albums/a160/turtl631/IMG_7041.jpg
http://i11.photobucket.com/albums/a160/turtl631/IMG_7042.jpg
http://i11.photobucket.com/albums/a160/turtl631/IMG_7043.jpg
Email me if you're interested in any of this, I check that quite a bit more than PMs and forums. [email protected]
Thanks for looking!
Greddy headgasket and valvesprings: I bought an SR from a local guy who was putting it in a Frontier, but his wiring job was botched and he never got spark, so it never started. He installed these parts but only turned the motor over with them.
The headgasket was torqued down properly with stock head bolts...it looks new other than a tiny scuff by one of the dowel holes. I measured it at 1.2 mm thick with an 88 mm bore, which seems to be the standard Greddy HG. $75 shipped
http://i11.photobucket.com/albums/a160/turtl631/IMG_7047.jpg
http://i11.photobucket.com/albums/a160/turtl631/IMG_7048.jpg
http://i11.photobucket.com/albums/a160/turtl631/IMG_7049.jpg
Greddy valvesprings- not much to say here, installed like the headgasket, but obviously wear is low on a set of springs that gets installed and then just sits other than being turned over a few times. $75 shipped
Crower retainers- Part number is 87097, they're just Crower titanium retainers (not BC pieces, but I don't know if there's any real difference). $75 shipped
Stance S14 GR+: These are 2.5 years old, with probably around 8000 miles on them. They have Z32 rear lower mounts, so they can only be run with Z32 rear spindles. As far as I can tell, they were made before Stance had these issues with crappy camber plates, as they haven't made any weird noises or failed in any way in the time I've had them. I'm also including the 9k and 7k springs, never used. I have the wrenches too, although they're a little bent. $700 (prefer local, but will ship)
http://i11.photobucket.com/albums/a160/turtl631/IMG_7040.jpg
http://i11.photobucket.com/albums/a160/turtl631/IMG_7041.jpg
http://i11.photobucket.com/albums/a160/turtl631/IMG_7042.jpg
http://i11.photobucket.com/albums/a160/turtl631/IMG_7043.jpg
Email me if you're interested in any of this, I check that quite a bit more than PMs and forums. [email protected]
Thanks for looking!