Long overdue Mega garage sale!!!

[mosill]

I used to be all over these forums a while back but school and my new car forced me to take a hiatus. I still a ton of old parts from my 240sx project and my family would love for me to get them out of the garage.

All the parts are located in Grand Prairie, TX (just outside of Dallas,TX).

I will list a rough price (as per mods request), not including shipping, but I can be pretty flexible and will say OBO on most of the parts.
***Again OBO on most parts so contact me***

Also, I will do my best to check the forum but you can def contact me at [email protected] .


Without further a due:

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/KA24E.jpg
KA24E motor.......$100
The motor had/has a knock. I never investigated since I only need the body for a shell. It would be good for parts or a rebuild.
Pickup only!!!

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/tranny.jpg
5spd tranny from my KA24E......$75
Should still be in good shape. I bought the car and immediately ripped out the motor/tranny.
Pickup only!!!

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/airbox.jpg
KA24E OEM airbox + piping.....$40

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/crossoverpipe.jpg
cross-over pipe for using a KA24 radiator with a SR20. Never used......$30

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/driveshaft.jpg
180sx driveshaft.... $50
It came with my clip but I just used my KA24 shaft.

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/fuelrail.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/fuel2.jpg
KA24E fuel rail.....$25

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/kainj2.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/kainj1.jpg
KA24E fuel injectors....$40



http://i67.photobucket.com/albums/h314/mosill/For%20Sale/misc.jpg
various heat shielding....$10
heater core...$25

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/rearend.jpg
rear subframe....$200
front subframe....$75
factory front/rear swaybars....$50
all from 180sx non-hicas clip

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/radiator.jpg
Koyo alumnimum radiator for KA24.... $150
it has never been used and has a couple slightly been fins from test mounting and storage.

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/steering.jpg
180sx steering coloumn...also from my 180sx clip...$50

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/struts.jpg
OEM suspension from the s13...$50
no idea how many miles were om them


*****************


http://i67.photobucket.com/albums/h314/mosill/For%20Sale/fanback.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/fanfront.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/fan22.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/fan21.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/fan12.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/fan11.jpg
radiator fans ....$30 per
one has one plug on the back and the other has 2.
I think one came from the KA24 and the other from my SR20 clip. Either can be wired to work just fine.

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/brakecylinder.jpg
brake mastercylinder from 180sx clip....$50


*******************


http://i67.photobucket.com/albums/h314/mosill/For%20Sale/ecu1.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/ecu2.jpg
KA24E ECU....$50

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/SOHCMAF2.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/SOHCMAF1.jpg
KA24E Maf.....$30

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/Ignchips.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/300ign2.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/300ign1.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/kaign.jpg
Ignitor chips...$50
all have been connecticity tested
2 from a 300zx/J30 with plugs+wires (one has tape b/c there was a chip on the case
and I wanted to make sure nothing got inside or shorted it)
1 from SR20 just clips


***********************


http://i67.photobucket.com/albums/h314/mosill/For%20Sale/shift1.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/shift2.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/shift3.jpg
JDM 180sx shifter from my 180sx clip.....$25

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/mount1.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/mount2.jpg
SR20 engine mounts...$40


****************************


http://i67.photobucket.com/albums/h314/mosill/For%20Sale/info1.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/info2.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/info3.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/info4.jpg

Greddy Informeter...........$225
The details can be seen here, Im too lazy too type anymore:http://store.phantasmusa.com/greddy16001601.html
I spent over 300$, after reservations + taxes, to buy it brand new and to be one of the 1st in the US to have one from Project Nissan.
It has never been used and only connected long enough to test. It can be used on a variety of imports and connects via OBDII or CONSULT port.
Sadly, this will not work on a car with Powerfc, like my 240 :(!

http://i67.photobucket.com/albums/h314/mosill/For%20Sale/kicker2.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/kicker1.jpg
Kicker 10" L5/L7 box. Great shape......$50

***************************


http://i67.photobucket.com/albums/h314/mosill/For%20Sale/band1.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/band2.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/band3.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/band5.jpg
http://i67.photobucket.com/albums/h314/mosill/For%20Sale/band6.jpg
12" sub bandpass box...$50
has one broken terminal but shouldnt cost more than $5 for a new one

I also have the OEM S13 blacktop SR20 intake manifold, but will have to take/post pics later....$50

[VIPDRFT]

PM'd you about the Koyo rad.

[penco]

$30 shipped for the radiator piping? And

[mosill]

I am willing to ship most parts, except the really heavy ones.

Make sure to give me your zip code so I can get an estimate for you.

Thanks,
Bryan

[mosill]

Bump... surely someone needs something.

Remember its all OBO.....so if you need something and think I'm asking too much contact me anyway so we can work something out.

[mosill]

LSD SOLD
Suspension SOLD