Best way to cut thru body?

[S13Boosts]

I need to go pickup a QP but i need to get it out my self whats the best way i should cut thru it? lmk thanks +1

[rps13drift]

electric shears!

[S13Boosts]

electric shears!


i have the ones you use by hand haha WORKS but slow ass fuck!:hs:

[japslapsilvia]

sawzall!! or angle grinder with cut off wheel

[rps13drift]

i have the ones you use by hand haha WORKS but slow ass fuck!:hs:

I know!!!! I cut most of my quarters out with the manual labor shears when i was doing my wide fenders! My buddy yelled at me and let me use his electric shears! So much better

[gotta240]

sawzall!! or angle grinder with cut off wheel


end thread. There is no other way.

I cut up an entire s14 this way.

[S13Boosts]

thanks guy! +1

[PITCH]

Hand held bandsaw. Cut off wheel would work best though.

[pbcstylez]

cutoff wheel or pneumatic shears

[96Turbo]

I need to go pickup a QP but i need to get it out my self whats the best way i should cut thru it? lmk thanks +1

you're picking up a quarter pound?!?!....jk

pneumatic shears cut through that flimsy nissan sheet metal like butta

edit...but since you probably won't have access to compressed air when ur cutting it off i'd go with a sawzall. won't take too long

[projectRDM]

Sawzall works fine, I've cut up over three dozen cars with usually a single blade per. Just make sure it's a decent model, anything below 7 amps is junk. I use a 13 amp Makita, it's got enough power to break the blade clean off instead of just binding and jerking your arm into the car like lesser models, which can generally leave a trail of blood or bruises.

[gotta240]

How far are you driving to do this? I have one already cut but i'm in san diego. Not sure if its worth the drive or if you were going to drive far anyways?

[huffandpuff00]

cutting wheel on 5" grinder. cheap and easy.http://i297.photobucket.com/albums/mm224/greysileighty/DSC_0611.jpg

[oneviaman]

plasma cutter!!

[90hatchie]

flame thrower!
jk

electric shears <3

[SR240DET]

what about drilling out the spot welds? it will have to be done anyways. To get my QP I drilled out the spot welds, cut the metal off at the middle of the rear window, side window, and wheel well.

[S13Boosts]

what about drilling out the spot welds? it will have to be done anyways. To get my QP I drilled out the spot welds, cut the metal off at the middle of the rear window, side window, and wheel well.


looks like alot of time LOL i just need to cut off the car & leave im not tryn to spend all day on it LOL!:ugh: im still thinking what should i use the cutoff wheels looks easy & cheap,Sawzall i dont have one & the electric shears i can prob get my hands on one


you're picking up a quarter pound?!?!....jk

i blew it all in 4 days :keke:

[s13drob]

+111

grinder w/ cut off wheel but it will be ugly. use whatever u think u got the best control with

[ZX88]

who uses power tools i rip that shit apart with my bare hands.:keke:

[S13Boosts]

who uses power tools i rip that shit apart with my bare hands.:keke:

no one can do that!:tweak: you atleast need to leave a little cut than rip that shit off hahaha if you dont care about it LOL!

[ZX88]

no one can do that!:tweak: you atleast need to leave a little cut than rip that shit off hahaha if you dont care about it LOL!

well after training lessons with arnold i can rip through anything. lol but on a serious note you could use one on the dremel tools with the circle saw head on it. its small and easy to manuver. ( i cant spell today)

[projectRDM]

well after training lessons with arnold i can rip through anything. lol but on a serious note you could use one on the dremel tools with the circle saw head on it. its small and easy to manuver. ( i cant spell today)

A dremel would take literally all day and a hundred blades (wheels). It would be a clean cut though.

[babowc]

I used a sawzall.
Works like a charm everytime

[Spring Break '92]

Cutoff wheel FTW. I just had a friend do my quarter panel a few weeks ago.
http://i76.photobucket.com/albums/j19/kooldevices/IMAG0013-1.jpg

[Addicted2Kouki]

Cutoff wheels...

they work.
any time i cut up a body panel, thats what i used.



either way, i thought they were gonna do the work?

[DUFFM4N]

plasma cutter!!

aka "the blue wrench" :keke:

[S13Boosts]

Cutoff wheels...

they work.
any time i cut up a body panel, thats what i used.



either way, i thought they were gonna do the work?


naw this is for my new QP that fucker told me to take it off LOL! so i need to go there & blah blah

[pbcstylez]

here get a 15" cutting wheel done and done

http://www.amazon.com/Makita-724603-3-14-Inch-Cut-Off-Wheels/dp/B0000223J6

get a portable angle grinder that can fit it, and itll take u less than 5 min

[S13Boosts]

here get a 15" cutting wheel done and done

http://www.amazon.com/Makita-724603-3-14-Inch-Cut-Off-Wheels/dp/B0000223J6

get a portable angle grinder that can fit it, and itll take u less than 5 min

^

DONE DEAL!

[BustedS13]

http://i30.tinypic.com/16c826t.jpg

sawzall
/thread

[DOOK]

plasma cutters are fun... they tear shit up fast

[waynehead05]

BustedS13 that pic makes me laugh hard.

[lflkajfj12123]

http://www.horrorstew.com/images/Chainsaw003.jpg

couldn't help it

[pablo180]

http://thinkinginprogress.com/wp-content/uploads/2007/12/lightsaber.jpg
Just make sure you dont dip into the fuel tank.

In all seriousness, cut off wheel would do the job. But for god sakes, wear some safety goggles.