240LE
07-01-2008, 06:39 AM
These are aluminum 30mm brake setup from a very low mileage 1991 300zx Turbo, the owner bought a Stoptech BBK. Everything is in excellent condition, rotors are good, pads have half life remaining, caliper finish is like new with slight surface rust from sitting in storage (should wipe off with wd-40). includes front + rear rotors, claipers,pads, brackets, and z32 lines. $450 picked up, Alexandria Va 22304
I am moving and already sold my 240sx, so these have to go.
http://lh3.ggpht.com/josephlewis1/SGV5AbdEOzI/AAAAAAAAAhY/VolpDP4cwu0/DSCN1640.JPG?imgmax=512
http://lh4.ggpht.com/josephlewis1/SGV5A4ij9mI/AAAAAAAAAhk/3sKvysotY8E/DSCN1641.JPG?imgmax=512
http://lh3.ggpht.com/josephlewis1/SGV5Bbl0UQI/AAAAAAAAAhs/PTTiUH-uyuQ/DSCN1642.JPG?imgmax=512
http://lh6.ggpht.com/josephlewis1/SGV5BirGu1I/AAAAAAAAAh0/aH6OQfegjVY/DSCN1643.JPG?imgmax=512
I also have a full set of 3000GT VR4 rotors that are HUGE!! If anyone is interested in a retrofit, they will need to be resurfaced. They are same bolt pattern as z32, very thick most likely 30mm, and probably roughly the same diameter as 350z rotors. Just make a reasonable offer. pick up only. Here are pics with a z32 front rotor sitting on top for comparison.
http://lh5.ggpht.com/josephlewis1/SGV5D0fYdrI/AAAAAAAAAic/LvrR8ML8Rqs/DSCN1648.JPG?imgmax=512
http://lh3.ggpht.com/josephlewis1/SGV5DCRtPjI/AAAAAAAAAiM/FLzod2xcLBs/DSCN1646.JPG?imgmax=512
http://lh5.ggpht.com/josephlewis1/SGV5CWYuYDI/AAAAAAAAAiE/e7VWTnGJmEo/DSCN1645.JPG?imgmax=512
http://lh3.ggpht.com/josephlewis1/SGV5CCWdlJI/AAAAAAAAAh8/GKwwA43i8_I/DSCN1644.JPG?imgmax=512
I am moving and already sold my 240sx, so these have to go.
http://lh3.ggpht.com/josephlewis1/SGV5AbdEOzI/AAAAAAAAAhY/VolpDP4cwu0/DSCN1640.JPG?imgmax=512
http://lh4.ggpht.com/josephlewis1/SGV5A4ij9mI/AAAAAAAAAhk/3sKvysotY8E/DSCN1641.JPG?imgmax=512
http://lh3.ggpht.com/josephlewis1/SGV5Bbl0UQI/AAAAAAAAAhs/PTTiUH-uyuQ/DSCN1642.JPG?imgmax=512
http://lh6.ggpht.com/josephlewis1/SGV5BirGu1I/AAAAAAAAAh0/aH6OQfegjVY/DSCN1643.JPG?imgmax=512
I also have a full set of 3000GT VR4 rotors that are HUGE!! If anyone is interested in a retrofit, they will need to be resurfaced. They are same bolt pattern as z32, very thick most likely 30mm, and probably roughly the same diameter as 350z rotors. Just make a reasonable offer. pick up only. Here are pics with a z32 front rotor sitting on top for comparison.
http://lh5.ggpht.com/josephlewis1/SGV5D0fYdrI/AAAAAAAAAic/LvrR8ML8Rqs/DSCN1648.JPG?imgmax=512
http://lh3.ggpht.com/josephlewis1/SGV5DCRtPjI/AAAAAAAAAiM/FLzod2xcLBs/DSCN1646.JPG?imgmax=512
http://lh5.ggpht.com/josephlewis1/SGV5CWYuYDI/AAAAAAAAAiE/e7VWTnGJmEo/DSCN1645.JPG?imgmax=512
http://lh3.ggpht.com/josephlewis1/SGV5CCWdlJI/AAAAAAAAAh8/GKwwA43i8_I/DSCN1644.JPG?imgmax=512