need work done? 714 socal area

[brndck]

ya i'm bored and have alot of time on my hands so if anyone needs stuff fixed or parts installed lmk. i'm not set up for fab work so i don't do cages or anything, but if it bolts on or off i can do it. i also have a fender roller so i can do that as well. i take $ beer or trades. i'm an ase master tech and know my shit when it comes to s-chassis. its easier and cheaper if you can come to my house but if not we can arrange otherwise. just in case anyone here hasn't seen it, here's a vid of me doing a motorswap in my driveway.
pm or call 562 519 5577
tyler
http://youtube.com/watch?v=cy5O5ZqwchY

[PhAtXSuMo]

dude! i favorited this video on my youtube haha

[Jerrys14q]

nice video im getting GR*pro coil spl tension rods and subframe spacers from powered by max. How about two 24packs and hopefully we dont get drunk before we finish.hahaha jk

[brndck]

nice video im getting GR*pro coil spl tension rods and subframe spacers from powered by max. How about two 24packs and hopefully we dont get drunk before we finish.hahaha jk

yes! bring beers and things! if u rly want help pm me.

[Xandy Boosts]

I have an exhaust leak on header to downpipe on stock DE. It's just the gasket I think

It should be an easy job but I have no garage to do it at. Let me know!

Do you have a press? I also have bushings that need to be pressed in

[drftem]

hey be careful i had my thread locked because i didnt pay some fee to advertise my services on here i offer the same kinda stuff but further south down in sandiego.

[YoungGun]

You have a fender roller? How much to pull rear fenders? And where are you located, i'm too young to bribe with beers so cash will have to due hahaha.

[brndck]

xandy that gasket should be easy. like a half hour or so (as long as the car isn't super hot) i don't have a press tho.

young gun, it depends on how much you want them pulled. i'm in huntington beach. shouldn't take more than an hour or 2 to pull em.

and mods, sry if u feel i'm violating anything, i'm sure you'll let me know if i am. feel free to pm me if so.

[blasting_speed]

I added you to my buddy list. ahahaha Just incase this thread gets locked. I need some help putting in coilovers. I'll send you a PM once i get them.

[brndck]

sw33t. lmk when u get em.

[flclsteve]

dude tyler i did not know that was ur youtube vid i was like holy shit way back in the day rofl

[brndck]

dude travis i did not know that was ur youtube vid i was like holy shit way back in the day rofl
tyler, not travis. lay off the :drinking:
it was only like 1.5 years ago. i do at least 1 driveway engine swap per year. its tradition.

[CusCo_S14]

hey travis when i can scrap the money to buy the ebrake assembly off u how to install

[brndck]

my name is tyler, but ya i can install em for u as well.

[CusCo_S14]

my bad saw steve post

[S13Boosts]

u tryn change a hg for me? its not an s chassis tho.. lmk +)

[1989rps13]

where exactly in socal you located at!?

[PhAtXSuMo]

^^ yeah was just going to ask the same thing

[ALEXTHESUS*PECT]

how much to install y33, (q45) lowering springs incase i am too lazy when i pick them up?

[vutony]

tyler is located in hb

[adrians_s13]

bump for Tyler and 1 really unique s13.

I still haven't had a chance to put in that rear caliper I got from you a few months ago, lol...

[brndck]

/\/\/\/\ git on it son! there's no time like the present.

[blitzsti22]

hey how much to put on some rear diff mounts and sub frame mounts

[brndck]

hey how much to put on some rear diff mounts and sub frame mounts

not sure what ur diff mounts ur referring to? just subframe collars like these?
http://www.prostreetonline.com/pso/images/products/MR-6275_m.jpg
or something else?

[ellisonrox]

definitely ready to get my fenders rolled.. how much?

[brndck]

definitely ready to get my fenders rolled.. how much?

depends on what wheels ur trying to fit and if u have rucas and camber plates or not. fender rolling can take anywhere between 1.5-10 hours depending on if you have paint, if you wanna be in the hella-flush-wheel-whore thread, or just wanna not rub. i could say "hey it'll be $100," but if u have a set of 18x9.5 front and 18x11 rears with low offsets, its gonna take most of the day and would definitely cost more than that.

[ellisonrox]

k you've got PM :wiggle:

[brndck]

pm replied....

[TravisSW]

Hey Travis, errr Tyler.

Lets replace some o-rings and some valve stem seals. hahah

[brndck]

oooh no spank you. i r not machine shop.

[Xandy Boosts]

were you at pipeline last night? with the rpf1 black hatch? his name started with a T too

anyways, Tyler. I stopped by Nissan to pick up a gasket and saw my friend workin there. He replaced the gasket for me and no more leaks! haha. Anyway I'll hit you up for other things if anything. Thanks though man

[brndck]

were you at pipeline last night? with the rpf1 black hatch? his name started with a T too

anyways, Tyler. I stopped by Nissan to pick up a gasket and saw my friend workin there. He replaced the gasket for me and no more leaks! haha. Anyway I'll hit you up for other things if anything. Thanks though man

ya thats mine. lmk if u need help with anything else.

[Xandy Boosts]

hahaha I was the guy that asked you, "hey are those the aspec blastpipes?"

I'll hit you up for sure next time I need something done...

[imnotmatt1189]

hey i need to get my fenders rolled so they don't rub... i have 16x8 +0 wheels... how much would you charge? please pm me

[jay c. sagano]

WOW... amazing work !!

[brndck]

hey i need to get my fenders rolled so they don't rub... i have 16x8 +0 wheels... how much would you charge? please pm me

its $25 per corner to start. if you have some extremely wide wheels that are gonna take all day to fit (not your case imnotmatt) then the rate will increase.

[blitzsti22]

hey i need to get my fenders rolled i got 18x9.5 +12 wheels i dont want them to rub on my s14 how much to get them rolled??

[markyboi]

motor mount replacement? how much?

[Addicted2Kouki]

How much to wash and wax my car? :]