View Full Version : Os Giken Super Single (sr)
yokotavia
06-04-2008, 07:42 AM
hey everyone i just purchased a used clutch. got the rebuild kit for it. now im just curious what Throw Out Bearing that is required for the OS Giken super single clutch for the s13 SR20det.
i dont want to ghetto rig it, shits gotta be done right.
just curious is everyone has ever used it, opinions overall and which TOB to use?
thanks in advance.:bigok:
Sileighty_85
06-04-2008, 07:46 AM
The OS Giken one
http://www.rhdjapan.com/jdm-low/OS-Giken-Release-Sleeve-Bearing-8664
yokotavia
06-04-2008, 07:49 AM
im hearing an OEM TOB is recommended.
how do you know i need the OS giken specific bearing?
Sileighty_85
06-04-2008, 07:51 AM
cuz the OS Giken uses a longer collar and the bearing is differnt
I have a twin plate so I know
I posted a pic of the difference between OEM and The OS Giken one in another thread
upSLIDEdown
06-04-2008, 07:53 AM
Yep, with most plate clutches like that, you need the manufacturer's TOB. I have an ORC Single, and it uses the ORC bearing, and it's quite different from the OEM one.
yokotavia
06-04-2008, 07:54 AM
alright. but, what if my super single is different.
im looking for people that have used this exact clutch before.
twin plate is a bit different from single
Sileighty_85
06-04-2008, 07:59 AM
well it more than likely thinner
regardless OEM will not work properly for the OSGiken
I did an Install on a twin plate using the OEM Collar but Used the OS Giken Bearing, The clutch did not disengage completely even with ajusting the MC rod, becuase the collar was differnt
so with a Single more than likely it wont disengage at all
You have to use the OS Giken Bearing the contact point for the Pressure plate smaller
So if you use a OEM bearing you will more than like break the PP Fingers or the collar
yokotavia
06-04-2008, 08:05 AM
domo.(thanks)
ill research some more and see how it goes.
thanks for the 1 minute man response too
http://osgiken.net/products/racingmultiplate.html
os says that you can run a nissan tob.
it comes off an early nissan truck.
here is the part number.
30502-14601
here is the p/n for the sleeve.
30501-N1600
Sileighty_85
06-04-2008, 08:13 AM
http://osgiken.net/products/racingmultiplate.html
os says that you can run a nissan tob.
it comes off an early nissan truck.
here is the part number.
30502-14601
here is the p/n for the sleeve.
30501-N1600
Well there ya go
I was reffering to not being able to use the OEM SR
yokotavia
06-04-2008, 08:18 AM
i love you.
msglength
vespaman
06-04-2008, 02:19 PM
okay that's the same problem i have when i bought my blitz active clutch and the problem solve by using TOB from datsun 510
fliprayzin240sx
06-04-2008, 06:16 PM
TOB is usually thinner on the single plates. Twins, you replace the carrier too...
Jorgs_7
11-02-2015, 07:33 AM
Extreme bump from the dead.
Jorgs_7
11-02-2015, 07:42 AM
Need clarification:
I have a Cusco Super single (OS giken? Same thing?)
Need the throw out bearing for it.
Any help?
vBulletin® v3.8.11, Copyright ©2000-2021, vBulletin Solutions Inc.