Dyno runGT30R see dyno graph

[STEVES14]

http://i30.tinypic.com/206kdar.jpg
:2f2f:
327whp

Mods GT30R A/R .63 , 740cc nismo injectors, Z32MAFS, JWT ECU
this run was at 14psi but the A/F were alittle lean 13.5-12.5

No cams and stock intake manfoild , and cheap ebay bottom mount manifold
that was supposed to used for a t28 cutt the flange off and put a T3 flange
turbo is V-band has a 5 bolt turbine housing

Feed back would be nice guys thanks

[sunnys14]

Nice power at just 1 bar.

[STEVES14]

Nice power at just 1 bar.

thnax man forgot to mention that the turbo isn't V-band and it has a 5 bolt rear housing (cheap my fault :) ) and it's a blacktop s13 motor

[turtl631]

13.5-12.5 is more than a little lean.

[smelly240]

12.5 isnt crazy lean at only 14psi

i mean for the street i wouldnt do it... 13.5 tho sucks.

[turtl631]

I wouldn't want to be leaner than 12:1 in boost on 93 octane. It doesn't really make much more power, and it's risky.

[STEVES14]

I wouldn't want to be leaner than 12:1 in boost on 93 octane. It doesn't really make much more power, and it's risky.

you are all very right no doubt about it.......going to tweak the fuel a bit with my ultimate the car is park no so in about a month im buying a set of tomei cams and cam gears and dyno it again the goal is 350whp at 14psi hope i can reach it :x:

any ideas or thoughts would be nice guys thanks for the replays

p.s after [email protected] [email protected] or more is next i wonder how long this motor will last :)if it makes through the summer i'll be lucky

[ROIDMONKEY]

you are all very right no doubt about going to tweak the fuel a bit with my ultimate the car is park no so in about a month im buying a set of tomei cams and cam gears and dyno it again the goal is 350whp at 14psi hope i can reach it :x: any ideas or thoughts would be nice guys thanks for the replays
Id like to see that. [email protected] pounds!! doubt it . just being realistic .

[STEVES14]

Id like to see that. [email protected] pounds!! doubt it . just being realistic .


will see when i install the cams and re tune the car

[STEVES14]

will see when i install the cams and re tune the car

if i install JWT s4 cams and cam gears @ what psi do you guys think i need to make 350whp hope less then 18psi ( i may be liven dreams but the dyno never lie's):x:

[turtl631]

You don't necessarily need cam gears with the JWT cams. I think they're pretty decent as-is, versus the BC cams that seem to need quite a bit a timing adjustment to work right.

With a healthy motor and good tune, 400 whp should be easy on a 30R. I would expect somewhere between 400-450 whp (dynojet) at 20 psi, and you probably would need to do around 13-15 psi to hit 350whp. There are some good dyno graphs for 30Rs and 3071Rs on freshalloy, not sure how many of them are posted here.


Eh, I just noticed that you have a ghetto exhaust manifold and stock IM. The numbers I mentioned above were cars on nice manifolds like Full-Race, with cams and Greddy IMs. The further you are from that, the less power you'll make.

[jr_ss]

Personally, I think bringing the car to 11.5-12:1 afr's and maybe 2-3 more psi and you'll see what you want. I don't think you need cams to reach that, but an IM would help to take advantage of the turbo's flow capacity and net higher numbers...

[STEVES14]

You don't necessarily need cam gears with the JWT cams. I think they're pretty decent as-is, versus the BC cams that seem to need quite a bit a timing adjustment to work right.

With a healthy motor and good tune, 400 whp should be easy on a 30R. I would expect somewhere between 400-450 whp (dynojet) at 20 psi, and you probably would need to do around 13-15 psi to hit 350whp. There are some good dyno graphs for 30Rs and 3071Rs on freshalloy, not sure how many of them are posted here.


Eh, I just noticed that you have a ghetto exhaust manifold and stock IM. The numbers I mentioned above were cars on nice manifolds like Full-Race, with cams and Greddy IMs. The further you are from that, the less power you'll make.

your absolutely right about that cheap [email protected]# exhaust manifold i have lol.......but a set of JWT cams and a full-race manfoild are being purchased as we speak but i don't know if i want to change my IM because i know one kid who did and his torque curve sucks.....don't want to kill my Torque curve but if i can hit 350whp on a set of cams and a new F.R setup and the correct exhaust housing this turbo is supposed to have i'll be a happy camper no doubt about it :boink: after i reach my goal if possablie ..........400whp is next ( hope i don't blow this thing up :duh: )


for all thoose who shared there thoughts thank you :bow:

[STEVES14]

your absolutely right about that cheap [email protected]# exhaust manifold i have lol.......but a set of JWT cams and a full-race manfoild are being purchased as we speak but i don't know if i want to change my IM because i know one kid who did and his torque curve sucks.....don't want to kill my Torque curve but if i can hit 350whp on a set of cams and a new F.R setup and the correct exhaust housing this turbo is supposed to have i'll be a happy camper no doubt about it :boink: after i reach my goal if possablie ..........400whp is next ( hope i don't blow this thing up :duh: )


for all thoose who shared there thoughts thank you :bow:

ALRIGHT GUYS stay tuned S3 cams and cam gears and a full-race manfoild
and a 4 bolt exhust housing are coming in a month and installed over the weekend when i get the parts so i'll keep you posted