PDA

View Full Version : Best "low" rails for S13?


Def
05-06-2008, 03:54 PM
Searched around and all I found is that it's common for most rails on sidemount seats to put the seat off center from the wheel.

Is there any general consensus on the rails that can go the lowest, are most centered, and don't flex on one side(single sided slider lock)?


Also any feasible mods to do to brackets to get them centered?

DreamN
05-06-2008, 03:57 PM
Bridge FG rails.

kensreliableb18b
05-06-2008, 03:59 PM
^yup fg rails. even with it being off, its not off by much (maybe like max a cm?) not important unless you have like OCD

LongGrain
05-06-2008, 04:02 PM
general consensus says bride FG are the best.

i have a buddy club super low down race spec rail and i dont really see how the bride one can be any better, its low, its sturdy, i have no complaints whatsoever, i think if it were any lower i think you might have trouble bolting a seat in there lol.

oh yea, and they are very centered.

burnsauto
05-06-2008, 04:12 PM
my mod done to my recaro+bride rail to make it centered to the steering wheel.
http://i34.photobucket.com/albums/d115/slavetopaint/IMG_2390.jpg

Def
05-06-2008, 04:23 PM
Yea, I saw that pic in my search. Maybe I'm just dense, but without the rails in front of me I can't tell what you modified.

What's the thought on NAMS rails? Not as good?

hippo_chips
05-06-2008, 04:42 PM
i have a buddy club super low down race spec rail and i dont really see how the bride one can be any better, its low, its sturdy, i have no complaints whatsoever, i think if it were any lower i think you might have trouble bolting a seat in there lol.

oh yea, and they are very centered.
For tall people, FG is better cause it's lower. I had both. I got mad after buying the buddy club rails, cause they weren't super low down. I was at near stock seat height in my bucket. Went to Aspec, like right after buying these rails, bought an FG rail and gained so much headroom. The difference between both are the seat mounts on the rails. Bride is simply L shaped.
http://i207.photobucket.com/albums/bb306/HippoChips/BuddyClubSLDvsBrideFG.jpg

hotlavaflow
05-06-2008, 04:46 PM
I don't have any personal experience but I hear alot of people talk about Nagisa Auto super low rails aren't those good?

I have Corbeau brackets modded to sit lower.

A Spec Products
05-06-2008, 05:15 PM
Yeah

Bride FG

If it aint broke don't fix it

They work well for S13/14 in all categories (low down, dual locking, etc)

The offset center thing is not a big deal

Bride addresses it http://www.tees-usa.com/seatrail_LowMax.html

They say it offsets 15mm towards the door side

I never really noticed it myself until someone mentioned it

I don't have any personal experience but I hear alot of people talk about Nagisa Auto super low rails aren't those good?

I have Corbeau brackets modded to sit lower.

Nagisa made two versions of rails:

Version 1 - single side locking, advantage is their slider adjustment and slider style was "OEM" so it slides more smoothly than other aftermarket sliders

Version 2 - dual side locking, these are very similar to Bride FG in terms of construction and slider style

Only downside is that Nagisa Ver II's are slightly more expensive than Bride FG's

Which is why I just say get Bride FG

Another thing is STOCK

If you find a Bride FG in stock, or you know you need a seat rail, get it AHEAD OF TIME

FG is always hard to stay in stock and hard to get, so the legit dealers that stock it get it through them

s13coupedrfter
05-06-2008, 06:18 PM
I have the NAMS super low and theyre ok. There is a offset from the center of the seat vs. steering wheel. I'll try to get pics up tommorow.

LongGrain
05-06-2008, 06:25 PM
For tall people, FG is better cause it's lower. I had both. I got mad after buying the buddy club rails, cause they weren't super low down. I was at near stock seat height in my bucket. Went to Aspec, like right after buying these rails, bought an FG rail and gained so much headroom. The difference between both are the seat mounts on the rails. Bride is simply L shaped.
http://i207.photobucket.com/albums/bb306/HippoChips/BuddyClubSLDvsBrideFG.jpg

my buddy club looks like your bride FG drawing, my brackets look nothing like your BC drawing...

my seat sits JUST above the floor, i barely have enough room for the slider lever...

hippo_chips
05-06-2008, 06:44 PM
These are how mine looked, had the weird shaped brackets.
http://i207.photobucket.com/albums/bb306/HippoChips/10-01-07_1737.jpg
Did you buy the BC rails new? Has to be custom brackets, cause all the BC rails I've seen online have the same brackets as mine. Unless, they made new versions.

!Zar!
05-06-2008, 06:46 PM
Bride FG or nagisa d-lock v2.

Only choices that I would suggest you go with.

g6civcx
05-07-2008, 06:38 AM
Bride FG or nagisa d-lock v2.

Only choices that I would suggest you go with.

I bought both from Logan. I prefer the FG more than the Nagisa. The Bride is much lower and moves more smoothly.

NooKa
05-10-2008, 06:30 PM
I've got the Nagisa V1, single lock. It's the first racing seat/rail I've ever had in a car, but it works fine for me. It seems very centered in regards to the steering wheel.

- Nick

Brian
05-10-2008, 06:32 PM
I'll tell you what


BRIDE FG rails



I have had a good handfull of them and have ZERO complaints.

NooKa
05-10-2008, 07:16 PM
I've got the Nagisa V1, single lock. It works fine for me, but then again this is my first racing seat. In regards to it being centered with the steering wheel, it's fine. I don't think it's off at all. Also it has the L mounting brackets, and the seat sits pretty low.

All and all, no complaints.

- Nick

I'm a retard, sorry for the double post. First one wasn't showing up.

FaLKoN240
05-10-2008, 11:15 PM
I've had both Bride and the Nagisa...

I prefer Bride.

I got rid of my Bride to get a Nagisa, then I went back to Bride and sold my Nagisa.

s14koukilove
05-10-2008, 11:57 PM
sorry to highjack for sec

i have some cheap Bomz racing seats for a S14. what is the best rail to use so that it sits low. they dont work on the stock rails.

][Deace
Jhh

LongGrain
05-11-2008, 12:02 AM
These are how mine looked, had the weird shaped brackets.
[IMG]http://i207.photobucket.com/albums/bb306/HippoChips/10-01-07_1737.jpg[IMG]
Did you buy the BC rails new? Has to be custom brackets, cause all the BC rails I've seen online have the same brackets as mine. Unless, they made new versions.

bought my rail brand new from JHP usa in february, Buddy Club Super Low Down Race Spec Seat Rail, my brackets are L shaped, just like the bride. mine look nothing like the ones in the picture you posted. i can take pics when i pick my car up tomorrow if you wish. my seat isnt even on the lowest setting in front, and its still almost touching the floor, i dont know how you can get any lower than that. and its perfectly centered to the wheel.

BlackZenkiS14
05-11-2008, 12:17 AM
I love my Bride FG's.

It actually sat the seat low enough for me to clear with a helmet, which i thought was amazing, because i've always had a hard time getting room to clear with all the brackets i've tried.

http://photos-d.ak.facebook.com/photos-ak-sf2p/v235/49/110/635255042/n635255042_2712451_5016.jpg

http://photos-h.ak.facebook.com/photos-ak-sf2p/v235/49/110/635255042/n635255042_2712447_3536.jpg

burnsauto
05-11-2008, 09:58 AM
Yea, I saw that pic in my search. Maybe I'm just dense, but without the rails in front of me I can't tell what you modified.

What's the thought on NAMS rails? Not as good?

those plates that have the ubber thick welds on them were added in on both sides of the seat. This shoved the seat more over to the center, and dead on with the steering wheel. Its easier on a bottom mount seat, but with a little thinking, can be done on a side mount as well.

!Zar!
05-11-2008, 10:43 AM
sorry to highjack for sec

i have some cheap Bomz racing seats for a S14. what is the best rail to use so that it sits low. they dont work on the stock rails.

][Deace
Jhh

You must have missed EVERYTHING posted in this thread huh?

If it's side mount then bride fg will work fine.

Yuri
05-11-2008, 11:27 AM
I have a set of Wisteria rails.
On the lowest setting you have to take out the carpet, or else the seat can't move.
Good luck finding them if you don't live in Japan though...

Def
05-24-2008, 01:49 PM
Ok... So I bought some super pimp Bride FG rails because I didn't feel like fabbing up stuff... and they simply don't work with the seat I have.

Has anybody gotten these things to work with a Recaro Pole Position? It seems it was designed for a narrower "JDM" type seat without any side padding like the one I have for my passenger side. The Recaro is about 0.75" wider, and it doesn't seem possible to get these rails to work with it. I've grinded on the brackets and gained about 1/4", but it's still not looking like it'll fit. I can raise the seat all the way up and possibly get them to bolt up to the car, but at that point... I don't know why I'd bother.

And can someone explain why they leave OVER an inch of space between the innermost rail and the trans tunnel once bolted up? It seems almost too stupid easy to move the slider over almost an inch towards the trans tunnel when making these rails.

I'll post some pics after I get some food. It's probably 100 degrees in my garage today and the Miller Lite isn't making it feel any cooler... bleh

spool_sample
05-24-2008, 02:47 PM
I'm wondering if the Nagisa D-Lock rails will work for you, Def.

I just bought some, and it looks like they might work with wider seats, and also let you move them over, since the mounting brackets have a pretty wide slot on them... not sure if the FG also has wide slots, though (didn't look like it from the pics I've seen). You could probably invert them, too, so you might have some options if you can get creative.

I'm glad I can fit in an SPG. :p

Here's what I'm talking about:
http://i39.photobucket.com/albums/e193/fullboost14/IMG_0220.jpg

http://i39.photobucket.com/albums/e193/fullboost14/IMG_0221.jpg

http://i39.photobucket.com/albums/e193/fullboost14/IMG_0223.jpg

Def
05-24-2008, 02:54 PM
I have a 30" waist, so I can fit into any of the smaller seats as well, I just got a ridiculously good deal on this Pole Position from my friend. It's not big of a seat, the padding still touches my hips, but it can fit someone with a 34" waist since it does have some padding.

It seems like it's a bit wider than the average non-FIA cert. seat, which I'm guessing is what these rails are designed around(i.e. Bride's overpriced non-cert seats).

nismostate
06-04-2008, 03:44 PM
Just mounted my fx1 pro w/ BC rails. yea bc sucks.. i sit higher on the lowest setting than my bottom mount bride knock offs with bride rails. not sure if bc rails are made only for bc seats but i barely have any headroom and im 5' 11". there's a lot of room under the seat to go lower too. looks like i need to make some L brackets to make it work right....:down:

BlackZenkiS14
06-04-2008, 03:54 PM
Im telling you man, you wont be dissapointed with FG rails. They are worth it.

Teddy
06-04-2008, 03:57 PM
Bride FG rails will sit you on the floor. Ask anyone who has sat in my car.

usdm180sx
06-04-2008, 04:07 PM
yes. teh FaG rails ftw

k's_silvia2.0
06-04-2008, 04:15 PM
I have a set of Wisteria rails.
On the lowest setting you have to take out the carpet, or else the seat can't move.
Good luck finding them if you don't live in Japan though...

And now........I owned them.:bigok:
Thanks again Yuri.

A Spec Products
06-04-2008, 04:16 PM
Recent thread with info on low rails

http://www.zilvia.net/f/showthread.php?t=194633&highlight=seat+rail

Def
06-04-2008, 06:27 PM
Yea, I mounted my no-name seat I got from a Japanese junkyard importer(actually fits me better than the PP, go figure) on the FG rails and it's pretty low. I'm 6'3" and now have about 6" of headroom at the lowest setting. Kind of weird driving the car now being so low, but it feels better.

The PP required me cutting and welding the brackets on my Recaro passenger rail(which was too narrow for my Recaro Pole Position strange enough) and bending the brackets a bit. At the lowest position I could get the seat in - the highest on the rails(they have a rail going between the sliders) the headroom is about the same as a stock seat with the seat cushion in, and you get about 2" more room taking the cushion out(thick compared to lots of seats).

berz
06-04-2008, 06:49 PM
im about to pick up a set of nrg seats cuzz im onn a money squeeze. so im trading them for my s14 seats plus 100 bucks , now the seller is stating that the seats sit high but not 4x4 high if at the worst case senario if its hella high and im only 5 '9 can i get the fg's and will they bolt up to the seats. btw i have a s13? thanks alot yall

A Spec Products
06-04-2008, 07:08 PM
im about to pick up a set of nrg seats cuzz im onn a money squeeze. so im trading them for my s14 seats plus 100 bucks , now the seller is stating that the seats sit high but not 4x4 high if at the worst case senario if its hella high and im only 5 '9 can i get the fg's and will they bolt up to the seats. btw i have a s13? thanks alot yall

I would just keep your stock S14 seats

Anyhow, if its a bucket seat then yes you can use a FG rail

If its a bottom mount reclinable then negative

berz
06-04-2008, 07:24 PM
so nrg for seats are boo boo??? thanks logan i guess im caught up in the black and red look of the seats , they are new seller states . thought it would be a come up ?????

wh0aitznic0
01-12-2009, 09:24 AM
I didn't want to make a new topic because this one was already up so...

Would the Bride FG rail work with the Wide Buddy Club bucket seat ? From what I've read, it leads me to say no because the FG doesn't work with the Recaro Pole Position which is just a tad wider than say a Zeta III.

g6civcx
01-12-2009, 09:58 AM
That's it. I've had it with these threads.

I'll post some pix later on with Bride and Nagisa rails to show you what's going on.

g6civcx
03-29-2009, 09:04 PM
Better late than never I suppose.

This is an excellent post. The depiction of the Bride FG is very accurate.

For tall people, FG is better cause it's lower. I had both. I got mad after buying the buddy club rails, cause they weren't super low down. I was at near stock seat height in my bucket. Went to Aspec, like right after buying these rails, bought an FG rail and gained so much headroom. The difference between both are the seat mounts on the rails. Bride is simply L shaped.
http://i207.photobucket.com/albums/bb306/HippoChips/BuddyClubSLDvsBrideFG.jpg

These are actual pix of my genuine Bride FG:

http://img8.imageshack.us/img8/8964/29232725.jpg
http://img21.imageshack.us/img21/7564/75046869.jpg

This is for comparison with a universal bottom mount rail available from Summit Racing. The seat is a Kirkey roadrace intermediate 15":

http://img23.imageshack.us/img23/9562/23680005.jpg

Assuming the seat is not too wide, the FG bracket does have some adjustments to accomodate various size seats. If your seat is too wide, you will have to fabricate your own mounting brackets to mount the seat to the rail.


Up close of one side of the rail for educational purposes. As you can see, the rail is sidemount. So the seat can go as low as possible until the seat hits the floor. There is nothing that goes under the seat from the rail. The rail is perfectly flat from where it mounts to the seat.

http://img16.imageshack.us/img16/1252/43098902.jpg

I offset the pix a little for perspective. As you can see, there is nothing sticking pass where the brackets mount to the seat. This means that the seat can go as low as you want until you hit the floorboard.

http://img11.imageshack.us/img11/9281/21575380.jpg