View Full Version : TSX projector retrofit
bananatree
03-10-2008, 04:06 AM
Finally start working on retrofit yesterday, and found out something.....didnt know its new or not, so just wanna share it
time: around 3 hours
ps: not the best write up(english limited)
throw in the oven(250F 10-15 min) for faster disassemble, heat gun took
forever.
http://i42.photobucket.com/albums/e334/x26ken/030708165921.jpg
cut down the stock silvia projector
http://i42.photobucket.com/albums/e334/x26ken/030708165907.jpg
trim it till you can slip through the front of the tsx projector, by this way, so you dont have to fabricate any branket hold the tsx pro into the right place.
you didnt even have cut the rear, the d2s bulb plugs right in the center.
http://i42.photobucket.com/albums/e334/x26ken/030708173044.jpg
alittle grinding on top of the tsx pro
http://i42.photobucket.com/albums/e334/x26ken/030708165850.jpg
drop in just like the orginal
http://i42.photobucket.com/albums/e334/x26ken/030708173130.jpg
back together, can adjust angle
http://i42.photobucket.com/albums/e334/x26ken/030708181528.jpg
alittle angle adjust on the light cutting line, wala
http://i42.photobucket.com/albums/e334/x26ken/031008013706.jpg
punxva
03-10-2008, 07:40 AM
very nice write up
markyboi
03-10-2008, 08:11 AM
subscribed!
+1 for you
los_inc
03-10-2008, 08:23 AM
awesome write up! i was wondering if you post pictures of the projector in the housing.
thanks again
-los
+1 for you sir
hayai_240
03-10-2008, 11:09 AM
It would also be really helpful if you could describe the wiring needed to properly set this up. Thanks
bigOdom1
03-10-2008, 11:11 AM
yeah make a list of the parts that came with the tsx projectors
otherwise nice job
bananatree
03-10-2008, 02:03 PM
It would also be really helpful if you could describe the wiring needed to properly set this up. Thanks
any D2S hid kit will work, plug and play to H1 connector(harness recommanded), no wiring needed
bananatree
03-10-2008, 02:11 PM
yeah make a list of the parts that came with the tsx projectors
otherwise nice job
all you need:
triple or double silvia s13 projector headlight
TSX projector
D2S HID kit
some screws(25mm), must long enough to go through silvia hosing and TSX pro
tools:
drill
anything can cut and trim down metel, I use a dremel rotary tool
philip screw driver
8mm socket
Ghostdrifter
03-11-2008, 12:18 AM
Can you tell me the diameter
http://img301.imageshack.us/img301/4613/tsxprojector1kx4.jpg (http://imageshack.us)
w0nderbr3ad
03-11-2008, 01:44 AM
hell yea a reason to save up for my next mod. +1 for you sir
fueled by hate
03-11-2008, 02:19 AM
take some output shots where there's some distance between your car and the wall.
[w]hite[r]abbit[x]
03-11-2008, 03:11 AM
I'd like to see front end shots of the car with those projectors. I kinda want to do something like this to my S14 kouki headlights.
Can you tell me the diameter
http://img301.imageshack.us/img301/4613/tsxprojector1kx4.jpg (http://imageshack.us)
TSX lens diameter is 2.5", so figure a few tenths of an inch more for the full bezel thickness.
pbcstylez
03-11-2008, 01:11 PM
http://i7.photobucket.com/albums/y286/pbcstylez/hid%20install/IMG_3148.jpg
http://i7.photobucket.com/albums/y286/pbcstylez/hid%20install/IMG_3141.jpg
http://i7.photobucket.com/albums/y286/pbcstylez/hid%20install/IMG_3066.jpg
http://i7.photobucket.com/albums/y286/pbcstylez/hid%20install/IMG_3058.jpg
http://i7.photobucket.com/albums/y286/pbcstylez/hid%20install/IMG_2945.jpg
heres some pics from my tsx retro on s14 kouki
jsut thought id share
http://i7.photobucket.com/albums/y286/pbcstylez/hid%20install/IMG_3148.jpg
http://i7.photobucket.com/albums/y286/pbcstylez/hid%20install/IMG_3141.jpg
heres some pics from my tsx retro on s14 kouki
jsut thought id share
Hole-e-shit
Not trying to rag on you, but was the front glass pitted to hell? that cutoff looks horrible.
pbcstylez
03-12-2008, 01:15 PM
Hole-e-shit
Not trying to rag on you, but was the front glass pitted to hell? that cutoff looks horrible.
YES lol it needs a good cleaning on the inside, plus i dropped my projector a few times during the install lol
i need to get new lenses
YES lol it needs a good cleaning on the inside, plus i dropped my projector a few times during the install lol
i need to get new lenses
OUCH
but yeah, nice work. greenkouki on hidplanet did hybrid rx330 AFS into his housing, and it's niiice and sharp.
pbcstylez
03-12-2008, 03:39 PM
yah im on hidplanet as well, i gottta figure out whats causing my distortion tho
Tops*
03-12-2008, 03:48 PM
Here's my TSX retro from ~50'. They were a little low when I took the pic. I bought $20 Philips 85122+ bulbs on eBay too. :keke:
http://i114.photobucket.com/albums/n245/Yuta_I/DSCF1460.jpg
Anto taught me a lot.
krazydriver
03-12-2008, 05:54 PM
Thanks for the info!
Tops... that cutoff is awesome! :bigok:
vutony
03-13-2008, 12:04 AM
the retro-fit is pointless if the cutoff is not something similar to these
http://i22.photobucket.com/albums/b331/Yanki01/2083616_227_full.jpg
http://i22.photobucket.com/albums/b331/Yanki01/2083616_217_full-1.jpg
http://i22.photobucket.com/albums/b331/Yanki01/2083616_216_full-1.jpg
bsilvias13
03-13-2008, 04:21 AM
wow that looks very good. great job!
the retro-fit is pointless if the cutoff is not something similar to these
Not completely true, it's better than a kit.
BUT you are right about the cutoff. Distorted cutoff = light being diffused = less output = not as bright.
YOU MAKE ME SO PROUD
*sniff
Here's my TSX retro from ~50'. They were a little low when I took the pic. I bought $20 Philips 85122+ bulbs on eBay too. :keke:
http://i114.photobucket.com/albums/n245/Yuta_I/DSCF1460.jpg
Anto taught me a lot.
Tops*
03-13-2008, 10:34 AM
Is that your retro, vutony? How is the cutoff vutony posted so much sharper than mine? What projectors are they? I took my pics from ~50', but my cutoff still isn't as sharp as vutony's from 25'. Do the glass headlights have any negative effect?
I NEED ANSWERS!!! I WANT ULTRA SHARP CUTOFF!!!
bloodangels13
03-13-2008, 10:55 AM
my cutoff sucks like no other... i need to source me some tsx projectors.. i got everything else... I assume it wouldnt make much diff on install in two projector J's model headlights right?
If ANYONE has some tsx projectors for sale or can get me some pm me the price shipped to 22043-1408 and ill paypal you the money to send them to me
Aoshi112
03-14-2008, 03:43 AM
join HIDplanet and look in the for sale section. Some as low as 120+ shipping
bananatree
03-18-2008, 04:42 AM
the retro-fit is pointless if the cutoff is not something similar to these
http://i22.photobucket.com/albums/b331/Yanki01/2083616_227_full.jpg
http://i22.photobucket.com/albums/b331/Yanki01/2083616_217_full-1.jpg
http://i22.photobucket.com/albums/b331/Yanki01/2083616_216_full-1.jpg
what car was that? sharpest even seen!!!
jdFKNmVRT
03-18-2008, 05:22 AM
you got pics from the front with the lights on, well not actually on but like just on the car...
supersayianjim
02-25-2015, 07:59 PM
sweet, bumping this because I need to do this
vBulletin® v3.8.11, Copyright ©2000-2021, vBulletin Solutions Inc.