Nismoknightska-t
02-06-2008, 08:59 PM
The motor only has 4k miles on it. Motor was built and installed at G-dimension around 3 months ago. 1k break in period with No boost. Tuned about 2 months ago for 303wheel on pump @ 14psi. Bigger Turbo and you are good to go for 500+whp.
picked up 6,500obo (socal)
Engine:
Fully Built long block (Ams advanced rebuild kit)
Arias .20 over Pistons with 8.8:1 Compression Ratio
AMS/Turbo240 Sportsman Series Connecting Rods
Clevite Main and Rod Bearings
Fel-pro Full Engine Gasket Set
Mr. Gasket Copper Exhaust Manifold Gasket
Arp Main/Head Studs
Cosmetic Head Gasket
New oem Timing Assembly Replaced
BC v3 cams 272/272
BC dual springs and retainers
BC valves .5 over
4 angle valve job
New valve seals
New oem oil pump kit
Nismo stat
Turbo kit: (less then 5k miles)
JGS cast manifold
JGS waste gate
JGS oil feed/return kit
JGS exhaust dumb tube
JGS turbo elbow
MR. gasket copper exhaust manifold gasket
Turbonetics 50trim (.63a/r)(polished)
3inch downpipe w/ flex pipe
Greddy s13 sr20det intercooler kit(polished out)
Custom hotpipe(polished)
Custom intake w/ topfuel filter
NGK wires
NGK sparkplugs
Koyo radiator
Polished valve cover
Nismo fuel pressure regulator
Small battery
Polished intake manifold (all smog removed)
Nismo 740cc injectors
Custom 8 puck clutch good for about 480tq
Nismo radiator cap
AEM EMS (tuned by g-dimensions)
AEM 3.5 bar
AEM AIT
pictures here
http://www.zilvia.net/f/showthread.php?p=1815496#post1815496
picked up 6,500obo (socal)
Engine:
Fully Built long block (Ams advanced rebuild kit)
Arias .20 over Pistons with 8.8:1 Compression Ratio
AMS/Turbo240 Sportsman Series Connecting Rods
Clevite Main and Rod Bearings
Fel-pro Full Engine Gasket Set
Mr. Gasket Copper Exhaust Manifold Gasket
Arp Main/Head Studs
Cosmetic Head Gasket
New oem Timing Assembly Replaced
BC v3 cams 272/272
BC dual springs and retainers
BC valves .5 over
4 angle valve job
New valve seals
New oem oil pump kit
Nismo stat
Turbo kit: (less then 5k miles)
JGS cast manifold
JGS waste gate
JGS oil feed/return kit
JGS exhaust dumb tube
JGS turbo elbow
MR. gasket copper exhaust manifold gasket
Turbonetics 50trim (.63a/r)(polished)
3inch downpipe w/ flex pipe
Greddy s13 sr20det intercooler kit(polished out)
Custom hotpipe(polished)
Custom intake w/ topfuel filter
NGK wires
NGK sparkplugs
Koyo radiator
Polished valve cover
Nismo fuel pressure regulator
Small battery
Polished intake manifold (all smog removed)
Nismo 740cc injectors
Custom 8 puck clutch good for about 480tq
Nismo radiator cap
AEM EMS (tuned by g-dimensions)
AEM 3.5 bar
AEM AIT
pictures here
http://www.zilvia.net/f/showthread.php?p=1815496#post1815496