Fs: MD s13/s14 parts sale

[Biggamehit]

All parts come from used s13 and s14 oem and aftermarket setups, they are located here at Andrews AFB Md ( Mapquest zip code 20762).. Pick Ups would be awesome, but im willing to ship at buyers expense ( will vary depending on size and weight,i will used my shippers account at mailbox etc so it will not be high at all) all parts came from working cars.

Paypal will be the primary method of payment
secondary will be U.S post office money orders.
[email protected]

Contact Me
Aim: Biggamehit
Yahoo: [email protected]
Msn:[email protected]

s13 distributer: $40
http://img224.imageshack.us/img224/6327/khpim0093gi6.jpg

s14 distributer: $40
http://img145.imageshack.us/img145/2876/khpim0114qd4.jpg

s14 Altenator: $45
http://img80.imageshack.us/img80/3987/khpim0095jl8.jpg

s14 Throttle Body: $20
http://img528.imageshack.us/img528/676/khpim0097jv1.jpg

Ka24de RevHard Manifold: $80 ( red circle is mig welding that was added after deep grin put hole in manifold.. its sealed and works fine.)
http://img523.imageshack.us/img523/2530/khpim0098wx3.jpg

Ka24de Ssac Manifold: Sold
http://img524.imageshack.us/img524/5174/khpim0100ux2.jpg

KA24d/de O.E Flywheel: $10
http://img263.imageshack.us/img263/9060/khpim0099yi7.jpg

KA24d/de XTD 11lbs Flywheel: $75
http://img144.imageshack.us/img144/7452/khpim0101sh0.jpg

KA24d/de Act Xtream 4puck Unsprung clutch disk: $45
http://img80.imageshack.us/img80/4151/khpim0102nc0.jpg
http://img187.imageshack.us/img187/186/khpim0106ei7.jpg

KA24d/de stage 1 xtd pressure plate: $25
http://img530.imageshack.us/img530/8792/khpim0103bk5.jpg
http://img523.imageshack.us/img523/7406/khpim0104hx5.jpg

KA24d/de O.E clutch kit: $40 ( came from S14)
http://img511.imageshack.us/img511/5935/khpim0108hj2.jpg
http://img528.imageshack.us/img528/2880/khpim0109co3.jpg
http://img340.imageshack.us/img340/7886/khpim0117oj1.jpg

S13/S14 Fuel rail with stock 270cc injectors: 25$ each
http://img507.imageshack.us/img507/3653/khpim0116sm8.jpg.

Garrett z31 T3 with 7 bolt Non-wasted flange: Sold
http://img505.imageshack.us/img505/5319/khpim0118ot7.jpg
http://img224.imageshack.us/img224/7333/khpim0119st2.jpg

Xs Power! T3: $15 ( Major axial and radial shaft play needs rebuild) Sold
http://img530.imageshack.us/img530/8518/khpim0120ss2.jpg
http://img528.imageshack.us/img528/844/khpim0121sy1.jpg

Ka24e/de Starter: $25
http://img80.imageshack.us/img80/4702/khpim0122ok6.jpg

KA24de A/C compressor: $15 each
http://img523.imageshack.us/img523/817/khpim0123bb8.jpg

s13 tranny speed sensor: $5
http://img340.imageshack.us/img340/6517/khpim0124ph8.jpg

S14 full upper engine harness: $70 ( only one plug is crushed but can still be used no cuts anywhere)
http://img256.imageshack.us/img256/2548/khpim0125wd0.jpg

s13 L & R Full head light assembly: $50
http://img407.imageshack.us/img407/82/khpim0126gd2.jpg

s13 intake manifold: $40 ( removed secondary butterfly valves for added flow and slight hp gains)
http://img146.imageshack.us/img146/814/khpim0127qi0.jpg

s13 Front Tockico HP Strut and drop zone 2in springs: $85 ( front struts are fine rear are blown)
http://img145.imageshack.us/img145/4792/khpim0128xn9.jpg

4lug ( 4x114) SE alloy wheels: $25 each ( Pick Up only)
http://img106.imageshack.us/img106/7895/khpim0132lx2.jpg

s14 guage cluster: $29.99
http://img523.imageshack.us/img523/5810/khpim0134ue3.jpg

s13 89 sidemarker lights: $5
s13 pignose smoked and cleared bumper lights: $15
http://img183.imageshack.us/img183/2710/khpim0135lq8.jpg

[Biggamehit]

wire harness sale pending.... still up for grabs

[Biggamehit]

SE wheels sold...

wire harness pretty much sold to a zilvia member...........

[Snoopy]

Send me better pics of the revhard mani

[Biggamehit]

the fitment on a s14 is much better than s13 as far as master cly clearance...... I was sporting a Z31 T3 and there was only enough room between the master cly and exhaust housing to maybe fit 3 razor blades sandwiched together between the two....

my motor with T3 on revhard manifold.

http://img99.imageshack.us/img99/5218/kp6100291dc4jh1.jpg

now as explained there was a slight hole becuase I grinded it down to far and didn't realize the metal was that thin right there.. basically for the figment, the manifold seems to bolt up better in the bottom mount position. and they kinda set the bolt holes up like so.....

i just filled the hole in with a 125amp Mig welder I didn't get a chance to grind it down honestly becuase i was busy helping my buddy weld up my Jgstools Manifold. but it seals i drove it for 2 days and no soot formed around the welds.. you can grind it down further



http://img140.imageshack.us/img140/2194/khpim0138mv0.jpg
http://img243.imageshack.us/img243/3575/khpim0140cy8.jpg
http://img256.imageshack.us/img256/5866/khpim0141os4.jpg
http://img98.imageshack.us/img98/9356/khpim0142jc7.jpg
http://img222.imageshack.us/img222/2030/khpim0143dv5.jpg

[1sloREX]

do u by any chance have motor mounts for sale? if yes i can pick up tomorow with cash

[Biggamehit]

na brother... i need some badly to so i can create some solid mounts.. sorry man.

[Biggamehit]

xtd flywheel sold

[Biggamehit]

guage cluster sold

wheels sold

wireharness sold

rev hard manifold sold

shocks and springs sold

side markers sold

s14 distributer traded

Speed sensor sold

other stuff ready to be shipped

[Biggamehit]

one fuel rail sold