PDA

View Full Version : Need help checking codes on E5 ecu


Jon-S14
05-28-2007, 11:38 PM
Does anyone know how I can check for codes on my E5 ecu off my s13 blacktop? There seems to be no led lights and could someone tell me how I can wire up Consult? If I wire it up like this link: http://www.plmsdevelopments.com/consult_wiring.htm will I be able to read codes then?

nissanguy13
05-29-2007, 03:19 AM
did you check and see if your check engine light blinks when you turn the ecu screw left then right? Did you try to turn the ecu screw to see what it would do? Is the key turned to on?

Jon-S14
05-29-2007, 09:12 AM
The CEL is not wired up. If I find the wires for it and wire it up, will I be able to read codes? My key is on the third position when i try to check (run position), not acc.

ecuastyle84
05-29-2007, 09:33 AM
this might help...courtesy of Kazuo:

this is general for 89-98 Nissan but most apply to the SR20 motor.
- to set car into diag. mode, with the key in the "ON" position, turn potentometer screw on ECU fully clockwise, then turn it fully counterclockwise. The LED on the ECU will begin to flash.
- first digit = LONG blink; second digit = SHORT blink (ex: 1... 1... 1... 1... then 1-1-1 equals 43 = TPS)

Error Codes
11 Crank Angle Sensor/Camshaft Position Sensor.
12 Air Flow Meter/Mass Air Flow Sensor.
13 Engine Coolant Temperature Sensor.
14 Vehicle Speed Sensor.
21 Ignition Signal.
22 Fuel Pump.
23 Idle Switch.
24 Throttle Valve Switch.
25 Idle Speed Control Valve.
28 Cooling Fan Circuit.
31 ECM.
32 EGR Function.
33 Heated Oxygen Sensor.
34 Knock Sensor.
35 Exhaust Gas Temperature Sensor.
36 EGR Control-Back Pressure Transducer.
37 Knock Sensor.
38 Right hand bank Closed Loop (B2).
41 Intake Air Temperature Sensor.
42 Fuel Temperature Sensor.
43 Throttle Position Sensor.
45 Injector Leak.
47 Crankshaft Position Sensor.
51 Injector Circuit.
53 Oxygen Sensor.
54 A/T Control.
55 No Malfunction.
63 No. 6 Cylinder Misfire.
64 No. 5 Cylinder Misfire.
65 No. 4 Cylinder Misfire.
66 No. 3 Cylinder Misfire.
67 No. 2 Cylinder Misfire.
68 No. 1 Cylinder Misfire.
71 Random Misfire.
72 TWC Function right hand bank.
73 TWC Function right hand bank.
76 Fuel Injection System Function right hand bank.
77 Rear Heated Oxygen Sensor Circuit.
82 Crankshaft Position Sensor.
84 A/T Diagnosis Communication Line.
85 VTC Solenoid Valve Circuit.
86 Fuel Injection System Function right hand bank.
87 Canister Control Solenoid Valve Circuit.
91 Front Heated Oxygen Sensor Heater Circuit right hand bank.
94 TCC Solenoid Valve.
95 Crankshaft Position Sensor.
98 Engine Coolant Temperature Sensor.
101 Front Heated Oxygen Sensor Heater Circuit right hand bank.
103 Park/Neutral Position Switch Circuit.
105 EGR and EGR Canister Control Solenoid Valve Circuit.
108 Canister Purge Control Valve Circuit.


SR20 ECU:

E5 is from a 94-96 180sx black top 5 speed
E6 is from a 94-96 180sx blacktop automatic
WC is from a 94-98 S14 Silvia
62 is from a 91-93 180sx or S13 Silvia 5 speed
61,63 is from a 91-93 180sx or S13 Silvia automatic
J4 is from a 97-98 180sx Type X 5speed

Jon-S14
05-29-2007, 04:25 PM
Thanks for the info but my problem is I have no led's on my ecu. I've searched and read somewhere that the E5 ecus dont have a led for whatever reason. Anyone else that could help me out?

sliEighty
03-22-2009, 09:20 PM
when you turn the screw on the ecu which way do you need to turn it once your done?