View Full Version : SR20DET TopMount, T3/To4e, TiAl 38mm, Q45 MAF
SETUP HAS BEEN SOLD.......
I was going to go with this setup on my SR20DET S13, but I have run out of funds and need to go with a more cost effective setup.
T3/To4e, AR .60, exhaust .63, stage 3 wheel
TiAL 38mm wastegate with blue spring
Custom Topmount fabbed to clear S14 brake booster and master cylinder in S13 chassis and reduce heat to those components from turbo
Q45 MAF, 90mm
1300 plus shipping takes it.
email me at
[email protected] or PM me here
http://i35.photobucket.com/albums/d186/Lilredrover/turbo.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/manifoldgate.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/engine.jpg
Will also take partial trade on coilovers and/or stock turbo setup stuff.
I need:
stock T25 with downpipe and elbow
feed and return lines
stock or aftermarket bottom mount manifold
stock injectors with caps for fuel rail and male plugins
stock MAF with intake and cone.
If someone were to have their whole stock setup just mentioned and a set of tein basics or something with camber plates I'd go straight up.
lotsa views, no comments?
GoodOl'S13
05-25-2007, 12:44 PM
do you have pics of the mani off the car ?
savannaae
05-25-2007, 12:48 PM
+1 for an IA member.
do you have pics of the mani off the car ?
granted :bigok:
http://i35.photobucket.com/albums/d186/Lilredrover/turbostuff001.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbostuff003.jpg
cjturbos14
05-25-2007, 01:28 PM
what are your expectations horsepower wise on this setup?interested
turbo is capable of 475+, I was shooting for closer to 425ish, too much higher than that and you get into oil starvation issues without addressing that.
steve shadows
05-25-2007, 01:37 PM
turbo is capable of 475+, I was shooting for closer to 425ish, too much higher than that and you get into oil starvation issues without addressing that.
are you sure about that? the inducer looks quite small for that kind of power on a 2.0 liter.
More like 400whp max compressor wheel, possibly a 50 trim?
bump for a very good deal and good luck with your sale
are you sure about that? the inducer looks quite small for that kind of power on a 2.0 liter.
More like 400whp max compressor wheel, possibly a 50 trim?
bump for a very good deal and good luck with your sale
No, I'm not sure of that but that is what an employee of mainstream performance down near atlanta told me it was capable of and according to them, it's 60 trim. but thanks for the bump and well wishes. Either way, 400 horsies are peeeeerty good :D
more pics:
http://i35.photobucket.com/albums/d186/Lilredrover/turbostuff006.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbostuff005.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbostuff004.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbostuff002.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbo005.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbo004.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbo002.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbo001.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbo003.jpg
bump cause I misspelled brake in the original post and just fixed it. This is truely a good deal for someone. I have over 1600 invested in this stuff in the EXACT same condition it is now. ALL of it is NEW, UNUSED, only mocked up in engine bay in my garage, out of the weather COMPLETELY.
:2f2f:<------- I need to be doing this with my S13 instead of this :loco:
Duosx
05-25-2007, 05:10 PM
hows the clearance with the hotpipe on and the hood closed? looks to me like they would hit for sure !
very interested if they fit well
hows the clearance with the hotpipe on and the hood closed? looks to me like they would hit for sure !
very interested if they fit well
won't close as in it's current configuration, once the housing is turned down it will clear fine.
I am firm on my price, I didn't put OBO for a reason. I'm already lossing 1/3 of the value on new parts. Paid close to ~18-1900 and asking 1300
brainfood
05-25-2007, 08:57 PM
I am down for the trade, I have all my stock stuff I can give up since i have aftermarket rail and injectors but I cant have my car in non working condition to send you the parts and make the trade. I will have my new daily running in about 2 weeks if you still have it I might hit you up for the trade.
I am down for the trade, I have all my stock stuff I can give up since i have aftermarket rail and injectors but I cant have my car in non working condition to send you the parts and make the trade. I will have my new daily running in about 2 weeks if you still have it I might hit you up for the trade.
look me up when you're ready and we'll find out.
burgy240
05-25-2007, 09:30 PM
What else needs to be doen to be up and running, other than clock the turbo, bigger injectors, and have it tuned
What else needs to be doen to be up and running, other than clock the turbo, bigger injectors, and have it tuned
I'm clocking the turbo right now. It has to sit at about a 20 degree angle toward the suspension tower to clear the wastegate which isn't a problem on my S13, S14s I doubt any problem, but don't know for sure. Other than bigger injectors and tune, you're gonna have to fab new intercooler piping and intake tube.
GSXRJJordan
05-26-2007, 04:18 AM
I've got the stocker w/Megan mani/dump/downpipe/etc can give ya a Greddy hotpipe too if you need it. I don't have any spare coilovers, but I can give ya some cash/direct you to an excellent hook up :) Shipping's gonna be a bitch... but I might be down to let the 'duece' sit for a while to do this swap. Let me know what you think ~
PM sent
New pic of setup with turbo turned down to clear wastegate.
http://i35.photobucket.com/albums/d186/Lilredrover/turbostuffclearance002.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbostuffclearance001.jpg
I may take coilovers in trade, I dont need super uber rare expensive stuff, so tein basic type with camber plates plus cash on your part. cuscos, ksports, megans, etc... I don't need zeal or kai office expensive uberlysexystuffkindasuspensionstuff :D
kernel
05-26-2007, 09:22 AM
how much for manifold and wastegate only?
how much for manifold and wastegate only?
I've got several people interested in the whole package deal, but if they don't end up wanting it, I can do 600 for the manifold and wastegate plus shipping. I've never shipped to canada before, is it A LOT more expensive. I guess when that time comes I can get your address and get a quote.
kernel
05-26-2007, 02:38 PM
ok, thanks. I might sell my turbo setup shortly, if it goes that way. ill come back to you.
ok, thanks. I might sell my turbo setup shortly, if it goes that way. ill come back to you.
sounds like a plan
I spun the turbo around and reinstalled in car so everyone could see what it would look like in it's final setup. I'm workin hard for this sale, I need this stuff gone can you tell, haha. The setup will not come with the elbow coupler unless it's an absolute deal breaker :D.
http://i35.photobucket.com/albums/d186/Lilredrover/turbostuffclearance019.jpg
http://i35.photobucket.com/albums/d186/Lilredrover/turbostuffclearance020.jpg
ghostracing
05-26-2007, 10:32 PM
hey man u still lookin for a trade? i have a t25 in good condition very little shaft play and the stock manifold i also i have the 180sx suspension strut and shocks all the way around id like to make a trade for some of your stuff what would u be willing to trade?
hey man u still lookin for a trade? i have a t25 in good condition very little shaft play and the stock manifold i also i have the 180sx suspension strut and shocks all the way around id like to make a trade for some of your stuff what would u be willing to trade?
PM me pictures. I don't like the sound of "very little shaft play" really. If I'm trading brand new stuff I want "no shaft play" kinda stock stuff haha. also, I have nice struts and coils on the car now, not looking for other struts and coils, I'm looking for coilovers.
s14nnyc
05-26-2007, 11:45 PM
I got a set of cusco coilover . How much more you want on top?
I got a set of cusco coilover . How much more you want on top?
PM me pics and details on coilovers, miles used, any leaks, degrees of adjustability, etc. All that will determine the cash on top of them.
I'm still waiting on a PM s14nnyc with info on the cuscos.
gsxr and I have a deal that looks like it's gonna happen however
benefitx
05-28-2007, 03:34 PM
bump for some really nice stuff...
bump for some really nice stuff...
thanks man, how is the spun bearing coming along?
I still got this stuff and no deal has been made yet.
I've decided to sell or trade items seperately:
Mani- 500
TiAL- 250
Turbo- 600
MAF- 110
all prices include shipping are are slightly negotiable.
sale pending on the whole shebang
vBulletin® v3.8.11, Copyright ©2000-2021, vBulletin Solutions Inc.