PDA

View Full Version : Apexi super suction z32 kit installation help


alonroz
03-30-2007, 04:19 AM
hey, just bought myself an Apexi super suction z32 kit including the hard metal pipe and the filter, pic of the kit:
http://i5.ebayimg.com/01/i/000/77/84/5e3f_1.JPG
if you nitice the smallest metal pipe that's in the middle of the intake, that's what my problem is, the old rubber intake had no hole like this one, the instructions are only in japanese and i did not find any in english!
the picture in the instructions say that it should connect to somthing...:bash:
thanx allot....

benefitx
03-30-2007, 05:39 AM
cap it off , i think its for recirculating your BOV but dont take it from me

Wei240
03-30-2007, 10:07 AM
i'm sure you have it on your old, but yeah, it's to recirculate your bov, and you should recirc anyways

DP_Michelle G
03-30-2007, 12:51 PM
are you using it for a sr?

punxva
03-30-2007, 03:23 PM
actually its for an oil catch can, if your not running one, then just cap it

Slidin240Wayz
03-30-2007, 03:44 PM
Smallest metal pipe- nipple for _____________


Not the one for the Oil Catch Can, but it is on the stock intake pipe.


Carlos

alonroz
03-30-2007, 05:21 PM
ok, looked again on the stock intake and it has this niple but it's capped off,
so what is it for?
BTW car's runing a stock dump valve...
and yeah its on an SR

Wei240
03-30-2007, 05:27 PM
well, on mine, there are 2 bungs, 1 is from the bov, the 2nd is from the catchcan,
on the redtop, there's a t fitting on the valve cover, one goes to the block towards the back (firewall), the other is a pipe back to the intake (in between is a catch can)

garbury
03-30-2007, 11:09 PM
the vacuum fitting went to the factory boost solenoid thing on my SR.

alonroz
03-31-2007, 02:59 AM
so is it ok to cap it or not?
do not have a catch can either...

garbury
03-31-2007, 10:15 PM
yeah, cap it up. You will be fine

alonroz
04-02-2007, 02:28 AM
what is it used for? just for my knowledge...

1320_power
04-16-2007, 10:06 PM
where can get that metal pipe kit at? been looking for one.

Manhitbytran
04-16-2007, 11:57 PM
where can get that metal pipe kit at? been looking for one.

check http://pipingpro.com

DJ_Sunrise
04-17-2007, 04:47 PM
mach iii accessories.. got mine for $225 shipped.. try google

-Bart

crescendo
08-19-2007, 01:15 PM
And what about the larger pipe? What does it connect to when using an FMIC?

MyLevinGTZ
08-19-2007, 09:57 PM
larger bung is for BOV re-circ
small vacuum bung is for stock boost controller

i have both capped but you can use either as nessecary.

sicarius82
08-19-2007, 10:23 PM
i have the same intake. use a combination of electrical/corrosion tape and heat shrink wraps. put a small tube of heat shrink wrap. then wrap about 6 inches of tape around the nipple, focusing on the top. bring the heat shrink wrap above the tape with it extending about 1/4 inch over the tip of the bung. use heat gun or sister's (mother's) hair dryer to shrink wrap the tape to the bung. voila, capped. do not try to put a screw in there because it doesn't have threads.