GTi-R Individual Throttles for RWD SR20

[entix]

Up for grabs is a set of GTi-R individual throttles, flipped/rewelded and modified to bolt onto an s13 sr20de/t. This came off of a running near stock rear wheel drive SR20DET and were very responsive. Theyre basically the most baller shit ever. I'm asking for only $350 + shipping for them. You're also welcome to come pick them up in Davis, Ca.

You can reply here, or contact me at [email protected]

http://www.mikeskillz.com/temp/gtir1.JPG
http://www.mikeskillz.com/temp/gtir2.JPG
http://www.mikeskillz.com/temp/gtir3.JPG

[punxva]

god damn what a deal if i had an sr20 i'd be all over this, good luck with the sale

[the head]

shipping quote to zip 50266 please

[brainfood]

What was used for engine managment? Just curious I was interested in this setup.

[entix]

The stock ECU was used, as it still pulls through the MAF.

All PM's replied to, and I will have shipping quotes in a couple hours when I get home.

[GSXRJJordan]

also fairly interested ~ let me know what shipping to 91020 would be

[brainfood]

The stock ECU was used, as it still pulls through the MAF.

All PM's replied to, and I will have shipping quotes in a couple hours when I get home.

thanks thats what I figured, probably well sell before I can scrap together the money but if not I am def. interested. Thanks

[egan]

G/L with hood clearance

[entix]

Hood clearance is not an issue, if you'll notice the 2nd part of the manifold slopes down, instead of up, since it has been reversed.

shipping to 50266 is $40
shipping to 91020 is $25

all other quotes have been PM'ed

[koukimonster139]

soo about that going on my s14 blacktop...

[BLiTz]

Yea, if someone can tell me if this will work of S14 Motor for shure then i will paypal right then...

[WILDACEX187]

sent u a pm. :bow:

[entix]

Pending sale to wildaxex197, I dont think this would fit an s14 motor, as its an S13 intake. Unless S13 intakes fit S14's? I'm pretty sure they don't, sorry :\

[entix]

Sale fell through, all PM's replied.

[entix]

Sold, I think.

[entix]

Fell through again, back up for sale. These are packaged and ready to go.

[decksy]

gawd i want this so bad..... stupid bank account.

[egan]

hmmm, odd. a guy did that here in MI and had to space the hood hinges and cut well into his hood. but if you say it works whatever. im KAT. just lookin out for potential buyers.

G/L with sale then....

[entix]

hmmm, odd. a guy did that here in MI and had to space the hood hinges and cut well into his hood. but if you say it works whatever. im KAT. just lookin out for potential buyers.

G/L with sale then....There are different ways to cut and weld the manifold. If you look at the pictures, you can see how low of an angle this manifold will make with the hood.

[crash course]

^^^yup this is the correct way to cut/weld the manifold. the other way is to cut the manifold at the surge tank and flip it. doing it this way will create fitment problems.

[VitaminT]

Fitment problems yes, better/straighter flow yes.

[20 til 3]

i pm'd you, jw/n if your interested...or anything your looking for?

[entix]

i pm'd you, jw/n if your interested...or anything your looking for?
No you didnt :confused:

[20 til 3]

hmm, tried again, if not i was wondering about kouki tails for trade or if you needed anything else that you would be willing too...skyline brakes? idk, let me know

[ViZion Zs]

this setup works very well used it before. you can also just snip out two small parts out of the hood brace.

[egan]

werd. i believe you. sounds good. people: *buy now!* *dont flake!* *throttle response!* *watch friends blow load on sight!*

good luck with sale. free bump. im out.

[ViZion Zs]

bryan buy them mang its helps alot...

[97S14Silvia]

Is it still for sale?

[97S14Silvia]

Please let me know if you still have this and are still trying to sell it. I am starting to put my motor back together after a rebuild next week so this is the one part I still haven't decided on.

[nissantuner22]

I'll do 300 shipped to 32935, can paypal you tommorrow.