FS Modded 1989 Nissan 240sx SR20DET Silvia front end

[psycko069]

Alright due to recent unforeseen circumstances I am putting my baby up for sale. If there is a reasonable interest and it will be financially beneficial in the parts I will part it out so please let me know if you want parts. Mind you I will need cash before parting to keep people from backing out. Now let’s get down to it. Keep in mind that there is less than 2000 miles on this vehicle since I built it..

• 1989 Nissan 240sx Hatchback gutted rear and carpets
• Welded 4 point roll cage with diagonal cross brace and harness bar by East Coast Race Cars
• Wangan style Fiberglass wing
• Complete S-13 front end conversion
• Walbro 255LPH fuel pump
• Rear mount battery kit
• Whiteline adj rear sway bar
• SPL subframe collars
• PowerSlot slotted rear rotors
• Hawk HPS rear pads
• CIP Motorsports Teflon coated SS rear Brake Lines
• NISMO tranny mount
• Megan racing test pipe
• HKS Hi-Power 85mm cat-back exhaust
• ACT 6 puck unsprung race disc with upgraded pressure plate
• NISMO engine mounts
• Megan Racing 3 inch downpipe
• 2-Sparco Clubman harnesses with shoulder pads
• 2-Sparco Torino 2 Reclinable Racing seats with sliders
• Sparco Lap 5 Steering Wheel
• Autometer Phantom Series Boost and Oil Pressure Gauges in a dual pillar pod
• Sony Xplod stereo CD/MP3 Receiver
• Kenwood front and rear speakers
• Greddy 3 inch turbo extension
• Redtop SR20DET motorset including 5 speed tranny and ecu
• Custom intake piping
• Greddy Airinx intake filter
• SOHC MAF
• Greddy oversize oil pan
• Whiteline adj front sway bar
• Tein adj tension rods
• Powerslot slotted front rotors
• Hawk HPS front pads
• CIP Motorsports Teflon coated SS front brake lines
• D-2 40 way adj coilovers
• New outer tie rod ends
• New clutch master and slave cylinder
• HKS Hyperground Kit
• NISMO adj fuel pressure regulator
• Greddy oil filter relocation kit
• B&M fuel pressure gauge
• Koyo Racing radiator
• Greddy Oil Catch can
• Greddy VSPL front mount intercooler
• CIP Motorsports custom hot pipe
• Greddy Type RS Blow off valve
• Kei Office KS05R 17x7 4/114.3mm front rims with 32mm offset wrapped in Kumho Ecsta 711 rubber size 215/45/17 with about 100 miles on them
• Kei Office KS05R 17x8 4/114.3mm rear rims with 35mm offset wrapped in Kumho Ecsta 711 rubber size 235/45/17 with about 100 miles on them

• Will also come with a full set of stock teardrop wheels with good rubber and an extra KA24 5 speed tranny

As far as I remember this is everything. If I can think of anything I missed I will post it up. This setup put down 213rwhp and 212rwtq on stock boost directly after the build. Since then there have been changes made and bugs worked out. It pulls much harder now. I have the dyno chart and video if there are questions. Pricing for the vehicle as a whole will be 7,500.00. Vehicle is located near Jacksonville NC. Buyer is responsible for all shipping fees if needed. There are no prices for parts because I don’t want to part it out. But as I said earlier, I will if there is enough interest in it. Prices for parts will be posted if the demand arises.…………

http://i88.photobucket.com/albums/k200/psycko069/240sxforsale007.jpg
http://i88.photobucket.com/albums/k200/psycko069/240sxforsale005.jpg
http://i88.photobucket.com/albums/k200/psycko069/240sxforsale004.jpg
http://i88.photobucket.com/albums/k200/psycko069/240sxforsale003.jpg
http://i88.photobucket.com/albums/k200/psycko069/240sxforsale002.jpg
http://i88.photobucket.com/albums/k200/psycko069/240sxforsale001.jpg

[psycko069]

nobody wants my baby???

[S13SilviaGirl]

Nice car, but you being in NC might hinder your sales possibilities. Maybe throw her up on ebay? Free bump and good lucck.

[Shaminii]

One question: What seats rails do you have on those Torinos? Bride rails?

[psycko069]

the seat rails are a custom one off that were fabbed when i was having the roll cage installed. we went through multiple configurations to get it right so i could sit in the seat with the helmet on and not have to worry about the roof or main hoop on the cage getting in the way.

[owinbush]

Will you take a trade

[jbj858]

off topic question..but i was hoping do you think you can get me a custom bracket made as well..im having problems finding a good bracket with my momo start bucket seat..its bottom mount too if that helps..i hope you can help a fellow member out..peace

[psycko069]

i am not considering any trades. this is the fourth vehicle in my driveway and i was told by my better half its time to get rid of one.

jbj858, if you were local i could get you a bracket made up. my welder would need you and your vehicle to get the seat right for your driving style and the way you sit. i suggest finding a reputable welder in your area and going to see them...

[jbj858]

i am not considering any trades. this is the fourth vehicle in my driveway and i was told by my better half its time to get rid of one.

jbj858, if you were local i could get you a bracket made up. my welder would need you and your vehicle to get the seat right for your driving style and the way you sit. i suggest finding a reputable welder in your area and going to see them...


thanks for the reply, too bad i havent gotten any good luck on finding a welding place to make me a seat bracket for cheap and decent work...o well good luck on your sale..PEACE

[psycko069]

6500 OBO!!! someone please come get this car...

[napoleon]

how much for motor set with all related swap parts and supporting mods? Shipped to 35757

[DSR_DriftS13]

how is the tranny? i had that same clutch/plate in my SR (before i sold it) and it ate up my flywheel, and i started getting grinds after i installed it also. how long has the clutch been in there, and how many miles (approx) have you put on it (the clutch)? im interested in the car otherwise, the tranny is the only thing that concerns me. im willing to throw you an offer, i just wanna know what you have to say about the tranny.

[psycko069]

the tranny was rebuilt before i built the car so it has less than 2000 miles on it. i have had no problems with it yet. shifts clean and holds gears well. i am not ready to part it out yet but i will let everyone know if i do.

[psycko069]

5500. this is as low as i can go. there is more than that in parts alone in this car. so there it is. 5500 FIRM!!!!!!!!!!!!!!

[napoleon]

so...you gonna part it out? I would happile take all the swap related parts. I have cash. PM me.

[dr1v3n]

is this car still available?

[psycko069]

the car is still available. i had someone come look at it tonight but hasnt bought it yet.

[adictd2b00st]

get my rx7 sold for me and i'll buy this :P

[mad_hatter]

ill give you $4500

[psycko069]

mad hatter thanks for the offer but this guy should be pulling through for 6k with a wideband and turbo timer installed on the car. thanks though.

[mad_hatter]

so the car is sold...or what wideband are you talking about?

[psycko069]

this vehicle has been SOLD! thankyou to everyone for their interest. if a mod could please lock or delete the thread. thanks again.

there is an innovate wideband and an apexi tt installed in the vehicle. i was going to take those out and they are not included in the price. this buyer wanted to keep them....